Oil pressure sender

See SIA10900 for replacement crush washer if required. Also known as Guzzi and Piaggio refs. 32768710, AP0956169, AP8550512, 486051, 58076R, 826161, 641541, AP9150414, 1A024308R. This oil pressure sensor requires thread adapter ELA88123 to fit to 4 valves per cylinder big twins

 32768710 GU32768710 32 76 87 10
 3276 8710 3276.8710 32.76.87.10

Also fits Aprilia 1000 RSV4 RF , BJ 2017 -, Aprilia 1000 RSV4 RR , BJ 2016 - 2016, Aprilia 1000 RSV4 RR , BJ 2017 -, Aprilia 1000 Tuono , BJ 2003 - 2003, Aprilia 1000 Tuono Fighter , BJ 2002 - 2005, Aprilia 1100 Tuono V4 RF , BJ 2017 - 2019, Aprilia 1100 Tuono V4 RR , BJ 2016 - 2017, Aprilia 1100 V4 Tuono Factory , BJ 2017 -, Aprilia 125 RS4 , BJ 2017 -, Aprilia 125 RS4 Replica , BJ 2017 - 2018, Aprilia 125 Tuono , BJ 2017 -, Aprilia 900 Dorsoduro , BJ 2017 -, Aprilia 900 Shiver , BJ 2017 -, Aprilia Atlantic 500-,

Dimensions:
M10 x 1 thread. 6mm spade

UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick, If this item is out of stock we do stock a like for like replacement, which is this item SIA27301 .

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 This part is due back in stock soon, call 01484 841395 to reserve yours

If you would like to be emailed once this item is available again then click here

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Dimensions:
120mm x 45mm diameter overall

8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.

From late 2015 onwards 1200 models used SIA06428

See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump



See ENA90948 for the oil filter cover o ring and SIA10900 for the sump plug seal

 30153000 GU30153000 30 15 30 00
 3015 3000 3015.3000 30.15.30.00

Dimensions:
84mm x 77mm diameter overall, for 19mm OD spigot. HF552 is probably Hi Flo alternative

High quality German made Mahle OE quality cartridge oil filter with sealing rubber.

From late 2015 onwards 1200 models used SIA06428

Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 14 sided oil filter which is compatible with our oil filter tools TOA41005 and TOA01200. This Mahle filter is shorter that the equivalent UFI filter. See ENA90948 for the oil filter cover o ring and SIA10900 for the sump plug seal

 30153000 GU30153000 30 15 30 00
 3015 3000 3015.3000 30.15.30.00

Dimensions:
75mm diameter overall

JMP cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Dimensions:
120mm x 45mm diameter overall

Copper crush washer for brakeline connections, fits standard banjo bolt

Two M10 washers required per banjo bolt. Interchangeable with SIA10900

 25656100 GU25656100 25 65 61 00
 2565 6100 2565.6100 25.65.61.00

M10 crush washer used for sump (small twins, V11 Sport), gearbox and drive box level and drain plugs. Also used for lower fork damper retaining bolt washer. Used for sump drain on Breva 1100, 1200, Griso etc..., bevel box washer on v85tt 01528930

Also known as Guzzi ref. 25656100, 01528930, AP9150472, 95100309, 887879, 25656102, 486075, AP8163091
These may be supplied as either aluminium or copper crush washers

 10528900 GU10528900 10 52 89 00
 1052 8900 1052.8900 10.52.89.00

Dimensions:
16.5mm outer diameter x 10.4mm inner diameter x 1mm

Stainless steel drain plug for drive box and gearbox, includes recess for crush washer to locate in. Also used as level plug on big twins and front sump drain on small twins.

Also known as Guzzi ref. 95980212, 95980610. Use crush washer SIA10900 with this bolt

95980214-z 95980214 GU95980214 95 98 02 14
 9598 0214 9598.0214 95.98.02.14

Dimensions:
M10

Drain plug for drive box and gearbox. Also used as level plug on big twins and front sump drain on small twins.

Also known as Guzzi ref. 95980212, 95980610. Use crush washer SIA10900 with this bolt

Sorry this part cannot be shipped to the US or Canada

6 month warranty on this part

 Sorry, this part is sold out

 95980214 GU95980214 95 98 02 14
 9598 0214 9598.0214 95.98.02.14

Stainless steel braided hose oil lines for heads on square barrel models. See ENA14662 if you also need threaded link to cylinder head

Always replace crush washers (SIA12200 x 2 and SIA10900 x 2) when replacing oil lines, you may also require our banjo bolt ENA95990. Also known as Guzzi ref. 01153600 and 01153602

 14153660 GU14153660 14 15 36 60
 1415 3660 1415.3660 14.15.36.60

Dimensions:
Reach of approx. 170mm from central banjo to head