UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick, If this item is out of stock we do stock a like for like replacement, which is this item SIA27301 .

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Dimensions:
120mm x 45mm diameter overall

Inlet rubber

Fits between exhaust manifold on cylinder head and carb. Use clip SSA25950

61114300-z 61114300 GU61114300 61 11 43 00
 6111 4300 6111.4300 61.11.43.00

Dimensions:
30mm internal diameter x 39mm

Throttle cable for models with standard high top PHF pumper carbs

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 14117555 GU14117555 14 11 75 55
 1411 7555 1411.7555 14.11.75.55

Dimensions:
897mm outer length, 105mm free length, 5.7mm barrel nipple, 5.7mm barrel nipple

Throttle cable for models with VHB square slide carbs

Replaces part number 17117560. We advise you to measure your existing cable before ordering in case you have a non standard set up. Two cables required per bike

 17117561 GU17117561 17 11 75 61
 1711 7561 1711.7561 17.11.75.61

Dimensions:
Inner: 1120 mm, Outer: 1020 mm

Collet for exhaust manifold, two required per cylinder

19025460-z 19025460 GU19025460 19 02 54 60
 1902 5460 1902.5460 19.02.54.60

Straight plastic fuel pipe connector for FUA30000

This quick release fuel line connector can be fitted to Norge models. Use high pressure pipe FUA82808 with this connector

 01106692 GU01106692 01 10 66 92
 0110 6692 0110.6692 01.10.66.92

Dimensions:
Length 51mm, OD grey clip 20 mm

Head gasket

Can be used in place of ENA19062 and Guzzi ref. B063099 but it is recommended to use a gasket sealant for this application

27022060-z 27022060 GU27022060 27 02 20 60
 2702 2060 2702.2060 27.02.20.60

Dimensions:
82mm ID for 80mm barrel

Top end gasket and seal set containing rocker cover, base and head gaskets plus top end O rings

Top end gasket set for one cylinder. Inlet manifold gasket ENA27155 and exhaust gasket ENA90718 available separately

Dimensions:
88mm square barrel

Spacer for swinging arm. Two required.

 12547200 GU12547200 12 54 72 00
 1254 7200 1254.7200 12.54.72.00

Dimensions:
30mm OD 17mm ID 7mm depth

Seal for valve cover

You may also require ENA93631 for the spark plug tunnel

30023700-z 30023700 GU30023700 30 02 37 00
 3002 3700 3002.3700 30.02.37.00

Dimensions:
2.6mm cross section