These clever spacers allow the fitting of the taper roller head bearings which are standard on later small twins in place of the often damaged and fiddly OE ball bearing races.The taper roller bearings last much longer and are easily replaced unlike the ball bearing races

This part consists of 2 x taper roller adapters and a pair of taper roller bearings, depending on the condition of your stem it may be necessary to shim the taper roller bearings. You may find that extra headlamp rubbers SUA39701 are required to take up the extra distance between the top and bottom yoke on the fork stanchions. See The Shed for instructions.

 Sorry, this part is no longer available.

 39515000 GU39515000 39 51 50 00
 3951 5000 3951.5000 39.51.50.00

Stylish guard to protect your centre stand from damage. This beautifully made part is manufactured from stainless steel plate for maximum protection and longevity. Drilled to save weight this is an essential accessory if you take your Stelvio off road

 Sorry, this part is no longer available.

Rear hugger finished in gloss black, this will protect your rear shock from road spray and grit. Mounts via three pre drilled holes and supplied brackets

Supplied with brackets, stainless fasteners and fitting instructions

 Sorry, this part is no longer available.

The SW-Motech EVO footpeg kit offers 36 options for the rider footrest position. The kit contains rotating elements with firmly interlocking teeth which allow you to move the standard position by up to 15mm. The position of the footrest can be adjusted so that it's lower or moved forwards or backwards as well as adjusted in terms of its angle to suit your individual needs. It mounts to the original parts of the footrest holder.

See this link for fitting instructions. Silver painted finish

 This part is available by special order, request a quote

Clever stand which makes working on your bike much easier! This stand clamps safely to the bolts just underneath the rider footrests, and allows you to lift the bike securely in a similar action to a centrestand.

Useful substitute for a centre stand.

Needs 2 x 18mm 0.5 inch drive sockets to fit a V11 (not supplied)

 This part is available by special order, request a quote

 979717 MG979717

HIgh performance aluminium velocity stack for airbox to throttle body union on single throttle body models. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434.

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 This part is due back in stock soon, call 01484 841395 to reserve yours

HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA85433 and V-Twin Boost - ACA85001 or ACA85002.

Customer Kev fitted this combo and called us the next day to say that his V85TT was transformed; the fluffy throttle response between 2k and 3k was gone and the engine pulled better. Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 This part is due back in stock soon, call 01484 841395 to reserve yours

Replacement clutch plate for single plate RAM clutches

Torque setting for fitting this is 25Nm with a thread locking compound

 This part is available by special order, request a quote

Light smoke large touring screen, 230mm taller than the standard screen

230mm taller than the factory screen. Manufactured from 4mm high impact acrylic

 Order now and we will post your order within 7 days.

The SW-Motech EVO footrest kit offers 36 options for the rider footrest position. The kit contains rotating elements with firmly interlocking teeth which allow you to move the standard position by up to 15mm. The position of the footrest can be adjusted so that it's lower or moved forwards or backwards as well as adjusted in terms of its angle to suit your individual needs. It mounts to the original parts of the footrest holder. Improve rider comfort with this quality kit.

See this link for fitting instructions. Silver painted finish

 This part is available by special order, request a quote