Shop headings: New Spares | Used Spares | Accessories | Brands
Dellorto V9 slide needle for VHB 30 carbs
Standard needle clip position is 2nd groove from top
This part is due back in stock soon, call 01484 841395 to reserve yours
13937700 GU13937700 13 93 77 00
1393 7700 1393.7700 13.93.77.00
£23.40
INC VAT
£19.50 EX VAT
Dellorto needle valve kit comprising of valve and felt washer. For PHF36 and PHM40 carbs
Also known as Guzzi ref. 076527649, 14939150 and Ducati ref. 076527645, 0765.27.645
2 in stock
14939150 GU14939150 14 93 91 50
1493 9150 1493.9150 14.93.91.50
Also fits Ducati 750/900 SS Koewe, Ducati 750 F1/Laguna Seca, Ducati 900 MHR, S2, Ducati 900 MHR-I, Ducati 1000 MHR-2,S2
£24.00
INC VAT
£20.00 EX VAT
Long throttle cable, runs from twistgrip to splitter under tank
Supercedes Guzi ref. 31117581
This part is due back in stock soon, call 01484 841395 to reserve yours
31117565-z 31117565 GU31117565 31 11 75 65
3111 7565 3111.7565 31.11.75.65
£25.00
INC VAT
£20.83 EX VAT
Dellorto accelerator pump diaphragm for PHF and PHM carbs
Also known as Guzzi ref 075527555
2 in stock
14931050 GU14931050 14 93 10 50
1493 1050 1493.1050 14.93.10.50
£29.00
INC VAT
£24.17 EX VAT
Manual left hand petrol tap with nut and fuel level sender. On and off settings.
Will also fit most other Moto Guzzi tanks from 1976 to 1991, these can be used to replace discontinued electric taps but please measure first and check you have space for outlet pipe
1 in stock
23105370-z 23105370 GU23105370 23 10 53 70
2310 5370 2310.5370 23.10.53.70
£29.00
INC VAT
£24.17 EX VAT
Special Inlet rubber with HT lead guide for late Dellorto PHM carbs with a inlet stub OD of 46mm
Use clip SSA45970
This part will only fit late PHM40 carbs with 46mm inlet stubs, we recommend measuring your carbs before ordering
2 in stock
£35.00
INC VAT
£29.17 EX VAT
Plastic inlet manifold, replaces unavailable aluminium manifold. Suitable for PHF 30 carb conversions on models previously fitted with VHB30 carbs. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. Carb mounts direct to this manifold (no inlet manifold rubber required)
Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts. Can be used to replace PHF30 inlet manifolds 17116265 and 17116365 which are no longer available. These manifolds exit the heads at a different angle to VHB manifolds and in some cases you may need to modify side panels to allow clearance for air filters
1 in stock
£39.00
INC VAT
£32.50 EX VAT
Plastic inlet manifold, replaces unavailable aluminium manifold. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. PHF36 carb mounts direct to this manifold (no inlet manifold rubber required)
Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts
This part is available by special order, request a quote
£45.00
INC VAT
£37.50 EX VAT
Short alloy bellmouth / trumpet intake with domed mesh for Dellorto PHF 30 and 36 carbs, screws to rear of carb replacing air filter
This part is available by special order, request a quote
£46.00
INC VAT
£38.33 EX VAT