Complete right hand PHF 30 carb, supplied ready to fit with cable adjuster. Suitable as a replacement for the discontinued square slide VHB30 carb

Jetted to suit your model.
M48 x 1.25 Threaded air intake connection.
44mm Rubber sleeve type engine connection. Cable type choke mechanism fitted, lever choke can be fitted if requested when ordering. Also known as Guzzi ref. 28112644 and 28112600.
Use FUA30611 manifold kit. For cables use CAA17562 with standard plastic twinpull twistgrip or CAA20000 with Tommaselli 2C twistgrip

 This part is available by special order, request a quote

 28112610 GU28112610 28 11 26 10
 2811 2610 2811.2610 28.11.26.10

Complete left hand PHF 30 carb, supplied ready to fit with cable adjuster. Suitable as a replacement for the discontinued square slide VHB30 carb

Jetted to suit your model.
M48 x 1.25 Threaded air intake connection.
44mm Rubber sleeve type engine connection. Cable type choke mechanism fitted, lever choke can be fitted if requested when ordering. Also known as Guzzi ref. 28112645.
Use FUA30611 manifold kit. For cables use CAA17562 with standard plastic twinpull twistgrip or CAA20000 with Tommaselli 2C twistgrip

 This part is available by special order, request a quote

 28112611 GU28112611 28 11 26 11
 2811 2611 2811.2611 28.11.26.11

Dellorto PHF36 DD right hand carb. This is a flat top carb with 90° angle adapter for the throttle cable. Supplied with cable choke set up. Carb body is darker than earlier versions

44mm inlet manifold connection, includes accelerator pump. Supplied with single banjo connector. These can be fitted to T3, Convert, 1000 SP and T4 if FUA30611 is fitted.
Carb normally supplied in the following specification:

• 60/3 slide
• 130 main jet
• 50 idle jet
• 70 choke jet
• 8.5 gram float
  
  

   This part is available by special order, request a quote

   28112650 GU28112650 28 11 26 50
   2811 2650 2811.2650 28.11.26.50

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Dellorto PHF36 DS left hand carb. This is a flat top carb with 90° angle adapter for the throttle cable. Supplied with cable choke set up. Carb body is darker than earlier versions

44mm inlet manifold connection, includes accelerator pump. These can be fitted to T3, Convert, 1000 SP and T4 if FUA30611 is fitted.
Carb normally supplied in the following specification:

• 60/3 slide
• 130 main jet
• 50 idle jet
• 70 choke jet
• 8.5 gram float
  
  

   This part is available by special order, request a quote

   28112651 GU28112651 28 11 26 51
   2811 2651 2811.2651 28.11.26.51

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Replacement Dellorto throttle slide for PHF36 carbs, the original slide is no longer available from Dellorto. To fit this slide you may need to make a minor modification to the slide or your carb body. This can be made with a small file or Dremel type tool, see these instructions for details

 This part is available by special order, request a quote

 75527554 GU75527554 75 52 75 54
 7552 7554 7552.7554 75.52.75.54

K&N high performance air filter

• High Air Flow with Excellent Filtration
• Designed to Increase Horsepower and Acceleration
• Washable and Reusable
• Will NOT Void Vehicle Warranty
• Lasts up to 50,000 miles before cleaning is required depending on driving conditions
• K&N Million Mile Limited Warranty�
• Emissions Legal
• Economical, a K&N Air Filter Will Last the Life of Your Bike
• Works with Original Equipment Manufacturer Vehicle Electronics
• Easy High Performance Add-on
• Environmentally Friendly

 This part is available by special order, request a quote

28113660-z 28113660 GU28113660 28 11 36 60
 2811 3660 2811.3660 28.11.36.60

Long alloy bellmouth / trumpet intake with domed mesh for Dellorto PHF 30 and 36 carbs, screws to rear of carb replacing air filter

 2 in stock

Short alloy bellmouth / trumpet intake with domed mesh for Dellorto PHF 30 and 36 carbs, screws to rear of carb replacing air filter

 This part is available by special order, request a quote

Special Inlet rubber with HT lead guide for late Dellorto PHM carbs with a inlet stub OD of 46mm

Use clip SSA45970
This part will only fit late PHM40 carbs with 46mm inlet stubs, we recommend measuring your carbs before ordering

 2 in stock

Plastic inlet manifold, replaces unavailable aluminium manifold. Suitable for PHF 30 carb conversions on models previously fitted with VHB30 carbs. Contains inlet manifold, gasket, O rings, clip and M6 bolts to secure to head. Carb mounts direct to this manifold (no inlet manifold rubber required)

Note that on models with M8 inlet manifold bolts and standard heads (T3, 1000 SP) it will be necessary to drill out the manifold bolt holes from 6mm to 8mm to reuse your existing bolts. Can be used to replace PHF30 inlet manifolds 17116265 and 17116365 which are no longer available. These manifolds exit the heads at a different angle to VHB manifolds and in some cases you may need to modify side panels to allow clearance for air filters

 1 in stock