Brembo PS 15 rear master cylinder for models with a remote reservoir. Supplied with operating lever. Mounting holes at 50mm centres

Also known as Guzzi ref. also known as Guzzi ref. 30666960, 65660200, 10477665, 31666990. Brembo ref. 10.2934.02 Discontinued by Brembo- See BRA19001 for alternative part

 Sorry, this part is no longer available.

 19667000 GU19667000 19 66 70 00
 1966 7000 1966.7000 19.66.70.00

Rear brake master cylinder PS 13C, foot operated.

Supercedes Guzzi ref. AP8113502. Guzzi recommend this part as the replacement for the PS12B master cylinder 27667015 fitted to the Quota 1000 and NTX models. Note that the mounting bracket on the Quota will need an additional hold drilling to fit this master cylinder (different mounting centres). NTX models will need a new bracket fabricating. See BRA28659 for overhaul kit

 This part is available by special order, request a quote

 30667030 GU30667030 30 66 70 30
 3066 7030 3066.7030 30.66.70.30

Threaded linkage block used on brake or gear linkages (varies by model). Screws to M6 threaded rod

Wears over time, so we recommend replacing if your gear or brake linkage is sloppy

 This part is available by special order, request a quote

 18257551 GU18257551 18 25 75 51
 1825 7551 1825.7551 18.25.75.51

Brakelight switch for handlebar master cylinder

As this is longer available you may wish to fit BRA01004 instead

 Sorry, this part is no longer available.

 28741100 GU28741100 28 74 11 00
 2874 1100 2874.1100 28.74.11.00

Brembo PS 12 front master cylinder overhaul kit / rebuild kit for models with a trapezoid handlebar mounted reservoir

This seal kit is also known as Brembo ref. 10.4090.20

 Sorry, this part is no longer available.

 28659300 GU28659300 28 65 93 00
 2865 9300 2865.9300 28.65.93.00

Rebuild kit for Brembo P32 rear caliper. This is a comprehensive overhaul kit containing replacement dust seals, fluid seals, o ring, bleed nipple, dust cap, washers, brake grease and caliper bolts. One kit required per caliper. Also suitable for some Ducati / Aprilia models.

Caliper seal kit

 This part is available by special order, request a quote

Rubber insert and plastic cap for PS 15 Brembo rear master cylinder reservoir, this type does not have a level switch. Also fits round Brembo PS 17 master cylinder reservoirs

Only for brake fluid reservoirs mounted on the PS15 master cylinder. Also known as Guzzi ref. 17661150. This cap does not contain a fluid level switch (your original cap may). Brembo ref. 110430820. Does not fit replica PS 15 master cylinders BRA10802 and BRA07338

 Sorry, this part is no longer available.

 14661100 GU14661100 14 66 11 00
 1466 1100 1466.1100 14.66.11.00

Also fits Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR

Brake pipe used for supplying front left hand caliper, screws directly into caliper

Original type rubber brakeline with chunky galvanized ends

 This part is available by special order, request a quote

17658860-z 17658860 GU17658860 17 65 88 60
 1765 8860 1765.8860 17.65.88.60

5 hole disc carrier finished in black

We recommend you check your bobbins, spring washers and circlips are OK as these may also require replacement. This is an update to the non floating disc ( 28613300 / 28613301 ) fitted to Lario, T5, SP II, Monza 2, V75 and V35 3

 This part is available by special order, request a quote

 28613770 GU28613770 28 61 37 70
 2861 3770 2861.3770 28.61.37.70

The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.

Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping! This banjo bolt can be used in place of a standard fine thread M10 banjo bolt. Supplied with crush washers. We recommend fitting one of these brake valves per caliper
The innovative stahlbus vent valve allows you to change the brake fluid easily and without help. Clean, totally safe and fast !
This auto bleed valve combines all these advantages:

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÜV Rheinland.
  See BRA41652 for bleed valve cover

   1 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]