Single stainless steel M10 banjo bolt with bleed nipple for Brembo fittings. Supplied with bleed nipple cap and crush washers. Perfect for bleeding up old P9, F08 and F05 calipers where the bleed nipple has broken off. This can also be used to add additional bleed points to linked systems where airlocks are causing problems

These can be used to replace the standard banjo bolt on CARC models. See alternative part BRA41653 for Stahlbus auto bleed banjo bolt

 More than 5 in stock

Also fits Benelli 250 TS

Pair of organic EBC FA244 front brake pads for P4 30/34 F calipers with two pad pins (Brembo 6800 and 9970 calipers)

Guzzi pad reference is 01654630. Also fitted to some pre 2001 Cali EV's - check how many pins your brake caliper has if ordering for a 1997-2001 Cali EV. Also known as Guzzi ref. 2B003313, 61340211A, 01654630, 07670810, 07BB1935, AP8133614, 883673, 2B005736

 More than 5 in stock

 32654610 GU32654610 32 65 46 10
 3265 4610 3265.4610 32.65.46.10

Pair of organic EBC FA256 rear brake pads

Twin pin fitting. Pre 2012 V7 models use a different brake pad with only one pad pin hole. Also known as Guzzi ref 2R000248

 2 in stock

AP8133798

Brembo M10 bleed nipple kit containing M10 bleed nipple and rubber cap. M10 bleed screw used only on rear of 2003 on models

Brembo no. 98.8249.20

 This part is available by special order, request a quote

 17659260 GU17659260 17 65 92 60
 1765 9260 1765.9260 17.65.92.60

Brakelight switch

Stop light switch also known as Guzzi ref. AP8224192
See FRA98412 for mounting screw

 3 in stock

03749845-z 03749845 GU03749845 03 74 98 45
 0374 9845 0374.9845 03.74.98.45

One litre AGIP brake and clutch fluid, this is a high performance DOT 3 and 4 fluid suitable for all Moto Guzzis

Mixes safely with other DOT 3 , DOT 4 and DOT 5.1 brake and clutch fluids. If you are having problems bleeding your brakes you may need one of our one way bleed nipples BRA41651 and BRA41650

Please note this part CANNOT be posted outside of the UK mainland area.

See BRA99014 for high performance alternative

 More than 5 in stock

99cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir

Brake fluid, oil and fuel resistant. This is long enough for the rear brake master cylinder on V50 II and V35 I

 More than 5 in stock

49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir

Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I

 More than 5 in stock

Kit containing 2 stainless steel M10 banjo bolts for Brembo brake fittings with copper washers

Supplied with 4 crush washers. Also known as Guzzi ref. 95990033

 2 in stock

95990028-z 95990028 GU95990028 95 99 00 28
 9599 0028 9599.0028 95.99.00.28

Also fits Laverda Jota

Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models

Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.

 5 in stock