HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434.

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 1 in stock

This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.

Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.

See installation instructions here.

 This part is available by special order, request a quote

HIgh performance aluminium velocity stack for airbox to throttle body union on single throttle body models. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434.

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 This part is available by special order, request a quote

Oil temperature sensor, brass threaded body

 This part is available by special order, request a quote

 887421 MG887421

Also fits Aprilia 900 Dorsoduro, Aprilia 900 Shiver

K&N high performance air filter, flat paper cartridge type for single throttle body models

• High Air Flow with Excellent Filtration
• Designed to Increase Horsepower and Acceleration
• Washable and Reusable
• Will NOT Void Vehicle Warranty
• Lasts up to 50,000 miles before cleaning is required depending on driving conditions
• K&N Million Mile Limited Warranty�
• Emissions Legal
• Economical, a K&N Air Filter Will Last the Life of Your Bike
• Works with Original Equipment Manufacturer Vehicle Electronics
• Easy High Performance Add-on
• Environmentally Friendly

 This part is due back in stock soon, call 01484 841395 to reserve yours

AP8104924

UFI 31 760 00 fuel filter, connectors not threaded. On late CARC models (e.g. Stelvio) check that the code 05107230 is present on the fuel pump flange

In tank fuel filter. Also known as Guzzi ref. 32106060, see FUA01091 for alternative filter from Mahle. See FUA20004 for fuel pipe clips for this filter and FUA81000 for in tank fuel hose

 More than 5 in stock

 01106090 GU01106090 01 10 60 90
 0110 6090 0110.6090 01.10.60.90

Also fits Aprilia Dorsoduro 1200 (2010-2013), Aprilia Dorsoduro 750 - ABS (2008-2015), Aprilia Dorsoduro 750 Factory - ABS (2010-2013), Aprilia Shiver 750 (2007-2009), Aprilia Shiver 750 (2010-2013), Aprilia Shiver 750 GT 2009, Aprilia Shiver 750 USA (2011-2014)

Air filter, flat paper cartridge type for models with single throttle body

See SIA10434 for a reusable performance air filter

 This part is due back in stock soon, call 01484 841395 to reserve yours

AP8104924

High pressure internal fuel line / submersible fuel line, suitable for immersion in petrol. You will need to cut this to length according to your model

Suitable for modern fuel. 100% ethanol resistant. High pressure fuel hose. This is designed for use submerged in petrol inside the fuel tank. See FUA00004 for pipe clips

 3 in stock

Pivot pin / needle suitable for PHF / VHB / PHM and PHBH carbs

Float pin also known as Guzzi ref. 17933167, 061527346

 This part is due back in stock soon, call 01484 841395 to reserve yours

 13933100 GU13933100 13 93 31 00
 1393 3100 1393.3100 13.93.31.00

Quick release coupling for fuel line, enables easier tank removal as QR connector can be located in a convenient location.

We recommend fitting this now before you snap the coupling on your fuel pump

 1 in stock