Oil temperature sensor, brass threaded body

 This part is available by special order, request a quote

 887421 MG887421

Also fits Aprilia 900 Dorsoduro, Aprilia 900 Shiver

This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.

Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.

See installation instructions here.

 This part is available by special order, request a quote

HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434.

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 1 in stock

HIgh performance aluminium velocity stack for airbox to throttle body union on single throttle body models. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434.

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 This part is available by special order, request a quote

K&N high performance air filter, flat paper cartridge type for single throttle body models

• High Air Flow with Excellent Filtration
• Designed to Increase Horsepower and Acceleration
• Washable and Reusable
• Will NOT Void Vehicle Warranty
• Lasts up to 50,000 miles before cleaning is required depending on driving conditions
• K&N Million Mile Limited Warranty�
• Emissions Legal
• Economical, a K&N Air Filter Will Last the Life of Your Bike
• Works with Original Equipment Manufacturer Vehicle Electronics
• Easy High Performance Add-on
• Environmentally Friendly

 This part is due back in stock soon, call 01484 841395 to reserve yours

AP8104924

Black phase sensor O ring

Also known as Guzzi ref. 847180 timing sensor o ring

 More than 5 in stock

 90706141 GU90706141 90 70 61 41
 9070 6141 9070.6141 90.70.61.41

High pressure internal fuel line / submersible fuel line, suitable for immersion in petrol. You will need to cut this to length according to your model

Suitable for modern fuel. 100% ethanol resistant. High pressure fuel hose. This is designed for use submerged in petrol inside the fuel tank. See FUA00004 for pipe clips

 3 in stock

Small stainless steel hose clip for fuel, oil and small breather pipe unions. Suitable for fuel injection hoses

 More than 5 in stock

Single T-shaped nylon fuel pipe connector for 6mm ID fuel pipe or breather pipe

 5 in stock

Quick release coupling for fuel line, enables easier tank removal as QR connector can be located in a convenient location.

We recommend fitting this now before you snap the coupling on your fuel pump

 1 in stock