Pair of sintered EBC FA256 HH rear brake pads

High performance sintered pads with twin pin pin fitting. Pre 2012 V7 models use a different brake pad with only one pad pin hole. Also known as Guzzi ref 2R000248

 This part is due back in stock soon, call 01484 841395 to reserve yours

AP8133798

Clutch cable

Clutch cable with ninety degree elbow at handlebar end. For Nevada models with chassis number starting ZGULME

 1 in stock

 32093060 GU32093060 32 09 30 60
 3209 3060 3209.3060 32.09.30.60

Valve Spring Upper Seat

Valve spring seat for 2 valve/cylinder models

 2 in stock

 31038015 GU31038015 31 03 80 15
 3103 8015 3103.8015 31.03.80.15

Complete clutch cable including rubber gaiter at handlebar end of cable

Fits Nevada 750 with chassis prefix ZGULK. We advise you to measure your existing cable before ordering in case you have a non standard set up.

 1 in stock

31093083-z 31093083 GU31093083 31 09 30 83
 3109 3083 3109.3083 31.09.30.83

Steering Head Bearing Spacer for base of steering stem

 This part is available by special order, request a quote

 14516700 GU14516700 14 51 67 00
 1451 6700 1451.6700 14.51.67.00

Rubber indicator stem with triangular foot for indicators LIA29662 and LIA29663

Attaches to bike via 1 x M10 stud

 Availability varies on this part, check availability

Red lens for rear light

 This part is available by special order, request a quote

31741760-z 31741760 GU31741760 31 74 17 60
 3174 1760 3174.1760 31.74.17.60

Ball bearing

Also known as Guzzi ref. 43615480

 Order now and we will post your order within 7 days.

92201225-z 92201225 GU92201225 92 20 12 25
 9220 1225 9220.1225 92.20.12.25

Fine thread screw in brakelight switch for linked system proportioning valve or splitter. See ELA12735 for rubber cap

Stop light switch also known as Guzzi ref. 63657000

 5 in stock

 79654116 GU79654116 79 65 41 16
 7965 4116 7965.4116 79.65.41.16

Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 GT/Sport Köwe, Ducati 750 Paso (1984-1992), Ducati 750 Sport, Ducati 750/900 SS Köwe, Ducati 750 F1/Laguna Seca, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR-I, Ducati 900 SS (1990), Ducati 906 Paso (1988), Ducati 1000 MHR-2/S2

Single stainless steel M10 banjo bolt with bleed nipple for Brembo fittings. Supplied with bleed nipple cap and crush washers. Perfect for bleeding up old P9, F08 and F05 calipers where the bleed nipple has broken off. This can also be used to add additional bleed points to linked systems where airlocks are causing problems

These can be used to replace the standard banjo bolt on CARC models. See alternative part BRA41653 for Stahlbus auto bleed banjo bolt

 More than 5 in stock

Also fits Benelli 250 TS