These clip ons pivot on the central bolt to adjust the handlebar angle, pull back angle is adjusted on the fork stanchion clamp. These clip ons are unsuitable for use with the PS12 handlebar master cylinder. Bar ends are held in by a rivet and some modification will be needed if you wish to fit bar end mirrors.

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated.
Note that on models with an electronic tacho (e.g. Cali 3) the stud hole spacing may be a few mm out and you will needto drill new stud holes in the rear of the surround. You may also need to very slightly enlarge the warning light holes

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

3 pipe connections on underside (large, medium and small diameters), plus connection for rocker cover breather pipes. Connects to ENA14157, ENA17700 and ENA95136

3 pipe connections, with integral non-return valve. Use breather pipe set ENA14157 with this box

Screen has a dark tinted finish and mounts to headlight. May be adapted to fit other models with a similar or smaller diameter headlight to a V7 / Breva 750 (210mm between mounting points). You will need to fit small spacers or washers inside the headlamp mounting points on models with a smaller headlamp (e.g. V50, T3 etc...). Screens available without fixings if you wish to fabricate your own brackets, or if you wish to replace a damaged screen- see FAA10012.
To simplify installation always mount a screen on to the mounting brackets before mounting the brackets on the bike

Screen has a dark tinted finish and mounts to headlight. Screens available without fixings if you wish to fabricate your own brackets, or if you wish to replace a damaged screen- see FAA10012
To simplify installation always mount a screen on to the mounting brackets before mounting the brackets on the bike. Does not fit V7 III Stone Night Pack model

To simplify installation always mount a screen on to the mounting brackets before mounting the brackets on the bike

Screen is raw grey ABS and mounts to headlight. Prime and paint to match your bike's paintwork for a unique and stylish look.
May be adapted to fit other models with a similar or smaller diameter headlight to a V7 / Breva 750 (210mm between mounting points). You will need to fit small spacers or washers inside the headlamp mounting points on models with a smaller headlamp (e.g. V50, T3 etc...). Screens available without fixings if you wish to fabricate your own brackets, or if you wish to replace a damaged screen- see FAA10002
To simplify installation always mount a screen on to the mounting brackets before mounting the brackets on the bike

Screen has a light smoke finish and mounts to headlight. May be adapted to fit other models with a similar or smaller diameter headlight to a V7 / Breva 750 (210mm between mounting points). You will need to fit small spacers or washers inside the headlamp mounting points on models with a smaller headlamp (e.g. V50, T3 etc...). Screens available without fixings if you wish to fabricate your own brackets, or if you wish to replace a damaged screen- see FAA10002
To simplify installation always mount a screen on to the mounting brackets before mounting the brackets on the bike