Stainless steel fasteners kit for VHB carb models without sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike

This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 145 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)

 3 in stock

Stainless steel front engine mounting bolt kit made specially for Gutsibits. Kit contains one long engine M12 x 1.25 bolt, one M12 half nut, one M12 crinkle washer and two standard M12 washers - all in A2 stainless steel

Made especially for Gutsibits the original bolts are prone to seizing in place so we recommend replacing with this quality stainless part. Also known as Guzzi ref. 03429500, 14429505

 Sorry, this part is no longer available.

14429500-z 14429500 GU14429500 14 42 95 00
 1442 9500 1442.9500 14.42.95.00

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Universal hydraulic brakelight switch. This hydraulic switch replaces discontinued brake light switches by bolting in place of a double banjo bolt on the handlebar or rear brake master cylinder

Especially suitable for replacing the standard switch on models where the front brakes have been 'de-linked'

 1 in stock

Stainless steel exhaust stud kit consisting of 4 x studs, 4 x dome head nuts, 4 x wavy washers and 4 x flat washers

On pre-1998 models we recommend combining with a pair of new exhaust polished aluminium flanges - EXA30032

 More than 5 in stock

 96508040 GU96508040 96 50 80 40
 9650 8040 9650.8040 96.50.80.40

M20 gearbox and drive box filler plug (big twins), drive box level plug (small twins), also used for cylinder head bolt

See ACA12600 for aluminium alternative that can be undone by hand. Includes recess for O ring ENA90203

 More than 5 in stock

 12022600 GU12022600 12 02 26 00
 1202 2600 1202.2600 12.02.26.00

M16 stainless steel full nut and thick washer for rear wheel spindle

Also referred to as Guzzi ref. 14634400 and 92602316

 More than 5 in stock

92602316-z 92602316 GU92602316 92 60 23 16
 9260 2316 9260.2316 92.60.23.16

Stainless steel drain plug for drive box and gearbox, includes recess for crush washer to locate in. Also used as level plug on big twins and front sump drain on small twins.

Also known as Guzzi ref. 95980212, 95980610. Use crush washer SIA10900 with this bolt

 More than 5 in stock

95980214-z 95980214 GU95980214 95 98 02 14
 9598 0214 9598.0214 95.98.02.14

Kit containing 2 stainless steel M10 banjo bolts for Brembo brake fittings with copper washers

Supplied with 4 crush washers. Also known as Guzzi ref. 95990033

 2 in stock

95990028-z 95990028 GU95990028 95 99 00 28
 9599 0028 9599.0028 95.99.00.28

Also fits Laverda Jota

A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple

Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787

See BRA36794 for rubber cap

 More than 5 in stock

Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,