Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Left hand Domino type switchgear with high and low beam, pass, indicator and horn switches. Same style switch as ELA01738

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. An indication of wire colours is supplied with this switchgear. Supplied with 9 pin block connector. NB does not have lights off - park - on function, you need this to be on your RH switch (e.g. ELA01729 ) or run lights always on

 This part is available by special order, request a quote

Regulator rectifier for Saprisa charging systems

Male spade connectors on regulator, may be supplied with 7 connectors - see the diagram on our technical documents page for help installing this part. The standard black block connector is not compatible with the updated 7 pin reg/rec, you will instead need to fit female spade connectors to your wires.

 This part is due back in stock soon, call 01484 841395 to reserve yours

28703800-z 28703800 GU28703800 28 70 38 00
 2870 3800 2870.3800 28.70.38.00

Marelli air temperature sensor

Supplied with screws. Two required per engine

 Order now and we will post your order within 7 days.

 30729330 GU30729330 30 72 93 30
 3072 9330 3072.9330 30.72.93.30

Ignition pickup and tacho sensor

Connector plug has two male spades. Also known as phase sensor. Used on models with the large Marelli P8 ECU. No longer available from Guzzi. Note 90° angle where cable exits sensor. See ENA90141 for O ring used to fit this part

 1 in stock

 29721660 GU29721660 29 72 16 60
 2972 1660 2972.1660 29.72.16.60

Starter motor deposit, buy this deposit if you are buying one of our reconditioned starter motors and we haven't already received your servicable exchange unit. This deposit will be refunded once we receive your complete reconditionable Valeo or Bosch starter and solenoid

 More than 5 in stock

Cut out switch, threaded body. Used as sidestand switch on big twins and clutch cut out switch on V7 series small twins and Breva 750

 This part is available by special order, request a quote

 29759150 GU29759150 29 75 91 50
 2975 9150 2975.9150 29.75.91.50

12 volt coil

Two required per bike, only for injection models

 Sorry, this part is no longer available.

 29716562 GU29716562 29 71 65 62
 2971 6562 2971.6562 29.71.65.62

Prolong battery life with this 9 stage smart battery charger, suitable for 6v, 12v AGM and lead acid batteries.

Weatherproof - suitable for use outside 6V / 12V 1A Auto-sensing charger. Suits all AGM, Lead Acid, Calcium and Gel batteries Charges 6v and 12v batteries Ring terminal and alligator clip harnesses included Spark proof Maintains full charge Simple, connect and wait for green light Overload / Short circuit protection See ACA96001 for a spare set of charging leads (e.g. for a separate bike).

 This part is due back in stock soon, call 01484 841395 to reserve yours

Marelli air temperature sensor

Supplied with screws. Superceded by ELA30330

 Sorry, this part is no longer available.

 30729331 GU30729331 30 72 93 31
 3072 9331 3072.9331 30.72.93.31