Polished aluminium distributor cover for models with points or electronic ignition. Alternative for plastic cover ENA14420

See SSA05025 for the screws which secure this dizzie cap

 1 in stock

14715420-z 14715420 GU14715420 14 71 54 20
 1471 5420 1471.5420 14.71.54.20

Brand new eagle badge to replace the faded one on your top yoke nut

 2 in stock

 17517700 GU17517700 17 51 77 00
 1751 7700 1751.7700 17.51.77.00

Dellorto kit containing mixture screw, o ring, spring and washer

For most VHB, PHBH, PHF and PHM carbs, check length before ordering, FUA60854 is alternative screw

 3 in stock

 13936600 GU13936600 13 93 66 00
 1393 6600 1393.6600 13.93.66.00

Black clutch lever

See CLA17605 for this lever in aluminium finish. Can also be inverted for use as a brake lever on V50 II and V35 I with cable operated brake

 1 in stock

14605750-z 14605750 GU14605750 14 60 57 50
 1460 5750 1460.5750 14.60.57.50

Top end gasket and seal set containing rocker cover, base and head gaskets plus top end O rings

Top end gasket set for one cylinder. Inlet manifold gasket ENA27155 and exhaust gasket ENA90718 available separately

 3 in stock

90 degree angle drive box for speedo and tacho cables, screws into rear of clock

Fits all 850/1000 models. Also known as cable gearbox

 3 in stock

 17768360 GU17768360 17 76 83 60
 1776 8360 1776.8360 17.76.83.60

Inlet rubber with HT lead guide. Fits between inlet manifold on cylinder head and throttle body or between throttle body and airbox

Also known as Guzzi ref. 03114370, 29114360. Use clip SSA45970.


Please note that if you are fitting this as a replacement to FUA30470 you may need to make some modification to the end of your airbox nozzle for a secure fit

 5 in stock

 30114370 GU30114370 30 11 43 70
 3011 4370 3011.4370 30.11.43.70

Pair of Givi crash bars finished in black. The heads and rocker covers are vulnerable on these bikes and can be badly damaged by even a minor accident, replacement cost can be more than £1000 so protect your bike with these bars.

Supplied with fitting hardware and instructions.

 1 in stock

Brake caliper rebuild kit for one P2 F08 (P8) caliper, contains 2 pairs of seals and O ring to seal the two halves together

This seal kit is for F08 calipers fitted to front of all these models. Also used on some Triumph Bonnevilles, MZs, Ducati 600 Pantah, 500 Pantah, 500 Sport Desmo, 500 GTV, 650 SL, 750 F1, 750 F1B, 750 Paso, 750 Sport, 900 MHR, 900 SS, 900 S2, 906 Paso, 100 R1, 100 S2 Desmo, Laverda Jota 1000 and Laverda 1200 Anniversary. Brembo ref. 120274110

 More than 5 in stock

 14659000 GU14659000 14 65 90 00
 1465 9000 1465.9000 14.65.90.00

Also fits Benelli 354, Benelli Sei, Ducati 250/350/450 Desmo (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)

Single replacement caliper piston for Brembo P2 F09 or P9 caliper as fitted to Spada rear.

NB you will require a pair of these. Also used on Benelli Sei rear. Corresponding caliper seal kit is BRA54722

 2 in stock

 20391310 GU20391310 20 39 13 10
 2039 1310 2039.1310 20.39.13.10

Also fits Benelli 900 Sei Rear (1983), Laverda 1000 RGS Fronts (1984)