Sump bolt kit containing all replacement stainless steel socket cap bolts for models without a sump extension fitted

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070)

 More than 5 in stock

Top end gasket and seal set containing rocker cover, base, head and exhaust gaskets plus top end O rings

Top end gasket set for one cylinder. Inlet manifold gasket FUA19115 available separately

 4 in stock

Full service kit for single throttle body models containing 1 x UFI oil filter, 1 x UFI air filter, 2 x NGK CPR8EB-9 spark plugs, 2 x rocker cover gaskets and all crush washers and O rings to complete a service on your bike

Save £'s by buying everything in a service kit

The oils you need are 2 x OIA01051 1 x OIA08194 + 1 x OIA08193. Order service oil kit OIA28001 if you require oil with your service parts. See FUA01090 for fuel filter

 More than 5 in stock

Full seal kit and gasket set for overhauling the rear drive box

Bearings available separately

 More than 5 in stock

Full gearbox seal kit and gasket set for overhauling 5 speed gearboxes on big twins

Bearings available separately and as kit GEA92000

 4 in stock

Top end gasket and seal set containing rocker cover, base, head and exhaust gaskets plus cylinder base O ring

Top end gasket set for one cylinder. Inlet manifold gaskets available separately

 4 in stock

Screw kit containing 28 replacement stainless steel socket cap bolts for timing cover, inlet manifolds and sump pan. Only one kit required per engine. See SSA87983 and SSA89291 for special rocker cover screw kits

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070).

Add a bit of sparkle to your V7!

 More than 5 in stock

Full service kit containing 1 x UFI oil filter, 1 x UFI air filter, 2 x NGK CPR8EB-9 spark plugs, crush washer and filter cover O ring to complete a service on your bike. See FUA01090 for fuel filter

Save £'s by buying everything in a service kit

Guzzi approved ENI oils and lubricants available separately. The oils you need are 2 x OIA01051 for the engine

 More than 5 in stock

1 litre of Agip SAE 10W fork oil. Eni Fork Oil 10W is a product designed for the motorcycle industry designed and developed for use in forks and shock absorbers, suitable for both road and off-road use. The product is part of the Fork Oil series, which includes products with a different viscosity gradient to be selected in relation to the manufacturer's requirements and/or the damping action desired. It is also possible to obtain intermediate grades by mixing with other Fork Oil grades.

As recommended by Guzzi. One litre will refill both forks on most models, check your manual for exact quantity required. 5W also available, use a combination of 5W and 10W to tune your damping more precisely

Eni Fork Oil 10W is equipped with appropriate rheological features such as low temperature fluidity, high viscosity index and a very low sliding point, which results in smooth and uniform suspension behavior in a wide range of temperatures.

This product is characterized by high anti-wear properties, which ensure high protection and long service life to the lubricating parts.

The corrosion-resistant properties of Eni Fork Oil 10W allow effective protection of surfaces against corrosive phenomena.

Eni Fork Oil 10W has the necessary properties for the correct operation of the lubricated equipment, such as low foaming, low air retention, stability in hot conditions, and compatibility with rubber materials (gaskets).
Please note this part CANNOT be posted outside of the UK mainland area. ENI oils were previously sold under the AGIP name

 More than 5 in stock

GU30530527

1 litre of fully synthetic Eni I-Ride Racing 10W-50. Eni i-Ride racing offroad 10W-50 is an innovative lubricant with top synthetic formula set up and developed to meet the lubrication requirements of technology advanced 4-stroke engines that are fitted in off-road and road motorcycles. The exclusive formulation of the Eni i-Ride racing 10W-50 has characteristics that offer maximum performance even in the presence of particularly high stresses such as engines subjected to 'Off-Road' use.

The highly accurate selection of the raw materials that form Eni i-Ride racing 10W-50 makes it possible to achieve the best lubrication conditions of all the mechanical parts of the engine under any extreme driving conditions.

The formulation of Eni i-Ride racing 10W-50 is designed to offer the perfect operation of oil immersed clutches even under limited engagements and disengagements, as required in an off-road use.

The particular additivation selected for Eni i-Ride racing 10W-50 is capable of ensuring a good engine detergency, in particular it has characteristics that allow efficient control of the formation of deposits areas submitted to high temperature.

Eni i-Ride racing 10W-50 has properties which effectively counteract the occurrence of wear in any condition of use.

Surpasses API SL, JASO MA and MA2. ENI oils were previously sold under the AGIP name. 4.9l of this oil required for V100

 More than 5 in stock