Manual left hand petrol tap with nut and fuel level sender. On and off settings.
Will also fit most other Moto Guzzi tanks from 1976 to 1991, these can be used to replace discontinued electric taps but please measure first and check you have space for outlet pipe
1 in stock
23105370-z 23105370 GU23105370 23 10 53 70
2310 5370 2310.5370 23.10.53.70
£29.00
INC VAT
£24.17 EX VAT
Manually operated fuel tap or fuel valve for models with carbs. Includes cable and remote side panel mounted knob
These new taps have a linkage that may be shorter than the original tap. In this case, you will need to swap over the linkage from your old tap and re-use it. Before using the tap you will need to release it by rotating the brass section behind the tap by quarter of a turn (anti-clockwise)
1 in stock
29105450 GU29105450 29 10 54 50
2910 5450 2910.5450 29.10.54.50
£32.00
INC VAT
£26.67 EX VAT
Inlet rubber with HT lead guide. Fits between inlet manifold on cylinder head and throttle body or between throttle body and airbox
Also known as Guzzi ref. 03114370, 29114360. Use clip SSA45970.
Please note that if you are fitting this as a replacement to FUA30470 you may need to make some modification to the end of your airbox nozzle for a secure fit
More than 5 in stock
30114370 GU30114370 30 11 43 70
3011 4370 3011.4370 30.11.43.70
£12.96
INC VAT
£10.80 EX VAT
Top end gasket and seal set containing rocker cover, base and head gaskets plus top end O rings
Top end gasket set for one cylinder. Inlet manifold gasket ENA14500 and exhaust gasket ENA90718 available separately
5 in stock
£14.40
INC VAT
£12.00 EX VAT
Carbon fibre tank pad with Moto Guzzi emblem
Stylish way to prevent your tank getting scratched, see ACA04001 for a plain black tank protector
2 in stock
£32.40
INC VAT
£27.00 EX VAT
Top end gasket and seal set containing rocker cover, base and head gaskets plus top end O rings
Top end gasket set for one cylinder. Inlet manifold gasket ENA14550 and exhaust gasket ENA90718 available separately
More than 5 in stock
£14.40
INC VAT
£12.00 EX VAT
Chromed fork stanchion
1 in stock
63525400 GU63525400 63 52 54 00
6352 5400 6352.5400 63.52.54.00
Also fits Benelli Sei 750 (series 2)
£138.00
INC VAT
£115.00 EX VAT
Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:
Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.
NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres
Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit
3 in stock
£175.00
INC VAT
£145.83 EX VAT
Replacement alternator brushes or brush kit for Bosch alternators
Also known as Guzzi ref 17712453
More than 5 in stock
14712453-z 14712453 GU14712453 14 71 24 53
1471 2453 1471.2453 14.71.24.53
Also fits Benelli 900 Sei (Series 2)
£10.00
INC VAT
£8.33 EX VAT
Brush kit for overhauling Bosch starter motor
The brush connections need to be soldered
3 in stock
£10.00
INC VAT
£8.33 EX VAT