Dimensions:
38mm ID x 44mm OD x 26mm
Exhaust gasket, silencer bush or muffler gasket shim for exhaust joint between silencer and downpipe
2 exhaust bushes required per bike
More than 5 in stock
91113826 GU91113826 91 11 38 26
9111 3826 9111.3826 91.11.38.26
£15.00
INC VAT
£12.50 EX VAT
Rubber cover for Domino clutch lever and choke cable
Clutch cable rubber
1 in stock
27663815 GU27663815 27 66 38 15
2766 3815 2766.3815 27.66.38.15
£8.40
INC VAT
£7.00 EX VAT
Dimensions:
35mm x 47mm x 7/9mm
Fork seal
2 required per pair of forks, no need to stack two seals per leg. Replaces Guzzi refs. 90403447, 90403448, 90403546
More than 5 in stock
90403449 GU90403449 90 40 34 49
9040 3449 9040.3449 90.40.34.49
Also fits Gilera Runner, Benelli Sei 900
£11.00
INC VAT
£9.17 EX VAT
Complete LED indicator with lead. Fits front left or rear right
1 in stock
2D000438
£45.00
INC VAT
£37.50 EX VAT
Dimensions:
2.5mm tip, 17.5mm shaft, 6.5mm threaded section
Dellorto kit containing mixture screw, o ring, spring and washer
For most VHB, PHBH, PHF and PHM carbs, check length before ordering, FUA60854 is alternative screw
3 in stock
13936600 GU13936600 13 93 66 00
1393 6600 1393.6600 13.93.66.00
£10.20
INC VAT
£8.50 EX VAT
Dimensions:
56mm x 54mm x 9mm overall
Pair of Brembo 07BB1408 carbon ceramic brake pads for Brembo P2 F08 (P8) calipers
For P08/F08 calipers. Front and rear pads for all models except P9 equipped Spada where these are only for front calipers
More than 5 in stock
28654601-z 28654601 GU28654601 28 65 46 01
2865 4601 2865.4601 28.65.46.01
Also fits Benelli 354 Rear, Benelli Sei Fronts, Ducati 250/350/450 Desmo Fronts (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso Fronts (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2 Fronts, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 RGS Corsa Rear, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 Fronts (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)
£31.50
INC VAT
£26.25 EX VAT
Dimensions:
38mm x 50 mm x 7mm
Rotational oil seal for crownwheel carrier in drive box on post 1974 big twins. Front crank oil seal on loop frame models
Also known as Guzzi ref. 90403850 and used on 850 GT and loop frame models for front crank oil seal ( 90403851 )
More than 5 in stock
90413850 GU90413850 90 41 38 50
9041 3850 9041.3850 90.41.38.50
£9.80
INC VAT
£8.17 EX VAT
Dimensions:
80mm mounting spacing
12 volt ignition coil for models equipped with points, Bosch or Motoplat ignition systems, includes HT lead. Terminal layout is different to original coils- see photos.
Not for Digiplex models. Also known as Guzzi ref. 19716500, 19716520
5 in stock
31716560 GU31716560 31 71 65 60
3171 6560 3171.6560 31.71.65.60
£38.10
INC VAT
£31.75 EX VAT
Dimensions:
120mm x 80mm x 53mm
Air filter, flat paper cartridge type for models with single throttle body
See SIA10434 for a reusable performance air filter
5 in stock
AP8104924
£17.00
INC VAT
£14.17 EX VAT
Dimensions:
120mm x 80mm x 53mm
Air filter, flat paper cartridge type for models with single throttle body
See SIA10434 for a reusable performance air filter
5 in stock
AP8104924
£17.00
INC VAT
£14.17 EX VAT
Secure online shopping 
