Full service kit for twin throttle body models containing 1 x UFI oil filter, 1 x UFI air filter, 2 x NGK BR8ES spark plugs, 2 x rocker cover gaskets and all crush washers and O rings to complete a service on your bike

Save £'s by buying everything in a service kit

Oils and lubricants available separately. The oils you need are 2 x OIA01051 1 x OIA08194 + 1 x OIA08193. Order service oil kit OIA28001 if you require oil with your service parts. See FUA01090 for fuel filter. Single throttle body 2012 onwards models will need service kit SIA28002 instead- if in doubt check which type of spark plugs your bike has.

 1 in stock

Rocker cover screw kit containing 16 replacement stainless steel socket cap bolts for round and square barrel engine rocker covers. Only one kit required per engine

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). This kit is for models without billet rocker cover protectors fitted, for models with rocker cover protectors see SSA80015. This kit will suit a V11 with standard rocker cover protectors which are much thinner than aftermarket types.

See SSA81522 for rocker cover trim retaining screws on 2v/cyl CARC models, these are not included with this kit.

 More than 5 in stock

Sump bolt kit containing all replacement stainless steel socket cap bolts for models without a sump extension fitted

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070)

 More than 5 in stock

Full service kit for single throttle body models containing 1 x UFI oil filter, 1 x UFI air filter, 2 x NGK CPR8EB-9 spark plugs, 2 x rocker cover gaskets and all crush washers and O rings to complete a service on your bike

Save £'s by buying everything in a service kit

The oils you need are 2 x OIA01051 1 x OIA08194 + 1 x OIA08193. Order service oil kit OIA28001 if you require oil with your service parts. See FUA01090 for fuel filter

 1 in stock

Top end gasket and seal set containing rocker cover, base, head and exhaust gaskets plus top end O rings

Top end gasket set for one cylinder. Inlet manifold gasket ENA27155 available separately

 1 in stock

Top end gasket and seal set containing rocker cover, base, head and exhaust gaskets plus cylinder base O ring

Top end gasket set for one cylinder. Inlet manifold gaskets available separately

 1 in stock

Screw kit containing 28 replacement stainless steel socket cap bolts for timing cover, inlet manifolds and sump pan. Only one kit required per engine. See SSA87983 and SSA89291 for special rocker cover screw kits

To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070).

Add a bit of sparkle to your V7!

 More than 5 in stock

The BoosterPlug is an effective and cost efficient way to cure the fuelling problems common to all modern fuel injected Guzzi's.
Plugging directly into the wiring harness using original connectors, with no cutting or splicing required, installation takes less than ten minutes.

The BoosterPlug features a unique technology to provide your bike with a controlled fuel enrichment in all ambient temperature situations. No other Plug and Play device does this. A richer mixture is provided only when needed i.e at low RPMs and when accelerating. On open roads at a constant speed the Boosterplug sits idle to keep fuel consumption low.
Make your bike run as it should have done from the factory!

• Improved and gentler throttle action when opening and closing throttle
• Richer mixture when opening the throttle improves acceleration
• Booster plug removes the uneven low speed running that is typical for modern lean burn engines
• Stronger and more consistent at idle.
• Reduced backfiring with aftermarket exhausts on engine braking
• Improved fuel economy

Exhaust stud kit consisting of 4 x titanium studs, 4 x stainless dome head nuts and 4 x stainless wavy washers

The mild steel exhaust studs fitted to modern Guzzis are notorious for corroding in place. Replace yours now with these corrosion resistant parts to ensure you can remove your exhaust in years to come

 This part is due back in stock soon, call 01484 841395 to reserve yours

1A003632R

1 litre of fully synthetic Eni I-Ride Racing 10W-50. Eni i-Ride racing offroad 10W-50 is an innovative lubricant with top synthetic formula set up and developed to meet the lubrication requirements of technology advanced 4-stroke engines that are fitted in off-road and road motorcycles. The exclusive formulation of the Eni i-Ride racing 10W-50 has characteristics that offer maximum performance even in the presence of particularly high stresses such as engines subjected to 'Off-Road' use.

The highly accurate selection of the raw materials that form Eni i-Ride racing 10W-50 makes it possible to achieve the best lubrication conditions of all the mechanical parts of the engine under any extreme driving conditions.

The formulation of Eni i-Ride racing 10W-50 is designed to offer the perfect operation of oil immersed clutches even under limited engagements and disengagements, as required in an off-road use.

The particular additivation selected for Eni i-Ride racing 10W-50 is capable of ensuring a good engine detergency, in particular it has characteristics that allow efficient control of the formation of deposits areas submitted to high temperature.

Eni i-Ride racing 10W-50 has properties which effectively counteract the occurrence of wear in any condition of use.

Surpasses API SL, JASO MA and MA2. ENI oils were previously sold under the AGIP name. 4.9l of this oil required for V100

 More than 5 in stock