Air filter, flat paper cartridge type
See SIA10425 for a reusable performance air filter
More than 5 in stock
AP8104242
£12.00
INC VAT
£10.00 EX VAT
5 pin mini relay
Also known as Guzzi ref. 30732560 Can be used in place of 4 pin mini relay ELA01561. We recommend keeping a spare one in your tool kit
More than 5 in stock
01731760 GU01731760 01 73 17 60
0173 1760 0173.1760 01.73.17.60
£14.00
INC VAT
£11.67 EX VAT
Speedo sensor with lead and 3 pin plug
Also known as Guzzi ref. 06765400. There are several variants of these sensors, please compare to the sensor on your bike or contact us with a chassis number before ordering
1 in stock
883768 MG883768
£62.00
INC VAT
£51.67 EX VAT
Final drive inner output seal
For Breva 750 from frame no. LL111908
4 in stock
90407591-z 90407591 GU90407591 90 40 75 91
9040 7591 9040.7591 90.40.75.91
£15.80
INC VAT
£13.17 EX VAT
Set of ignition points (made up of two boxes of contacts)
More than 5 in stock
19709620 GU19709620 19 70 96 20
1970 9620 1970.9620 19.70.96.20
£32.60
INC VAT
£27.17 EX VAT
Fork seal
2 required per pair of forks, no need to stack two seals per leg. Replaces Guzzi refs. 90403447, 90403448, 90403546
More than 5 in stock
90403449 GU90403449 90 40 34 49
9040 3449 9040.3449 90.40.34.49
Also fits Gilera Runner, Benelli Sei 900
£11.00
INC VAT
£9.17 EX VAT
Updated bush with thicker rubber section for front of torque arm / cardan arm / reaction rod on CARC models
1 in stock
883045 MG883045
£28.00
INC VAT
£23.33 EX VAT
8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump
See ENA90948 for the oil filter cover o ring
More than 5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£10.00
INC VAT
£8.33 EX VAT
A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple
Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap
More than 5 in stock
Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,
£8.00
INC VAT
£6.67 EX VAT
49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir
Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I
More than 5 in stock
£8.80
INC VAT
£7.33 EX VAT