Zadi ignition switch with 2 keys

4 male spade type connectors on underside, replaces original switch with bullet connectors. See ELA10005 for female spade connectors and FRA19741 for rubber wiring boot

 More than 5 in stock

 31735360 GU31735360 31 73 53 60
 3173 5360 3173.5360 31.73.53.60

Also fits Benelli 750 Sei (series 2) - fits with minor modification

Stainless steel front engine mounting bolt kit made specially for Gutsibits. Kit contains one long engine M12 x 1.25 bolt, one M12 half nut, one M12 crinkle washer and two standard M12 washers - all in A2 stainless steel

Made especially for Gutsibits the original bolts are prone to seizing in place so we recommend replacing with this quality stainless part. Also known as Guzzi ref. 03429500, 14429505

 Sorry, this part is no longer available.

14429500-z 14429500 GU14429500 14 42 95 00
 1442 9500 1442.9500 14.42.95.00

Chrome bar end mirror with a large round head and adjustable arm. Fits all models with open ended (i.e. not threaded) 7/8 inch steel handlebars.

Can be fitted on either left or right hand side of handlebars. Shown here fitted to a handlebar which is not included

 1 in stock

Old type 4 pin starter relay in metal case. Note that this has two large terminals and two smaller ones, depending on model you may need to fit wider spade connectors to fit this relay. See ELA10003 for large female spade connectors

 This part is due back in stock soon, call 01484 841395 to reserve yours

 12732500 GU12732500 12 73 25 00
 1273 2500 1273.2500 12.73.25.00

Pair of black side panel grilles for metal side panels, attach via 4 pins and clips (FRA39922)

Black side panel trims

 This part is available by special order, request a quote

 17925100 GU17925100 17 92 51 00
 1792 5100 1792.5100 17.92.51.00

Small round left hand bar end mirror finished in black. Knuckle allows adjustment of mirror. Fits all models with open ended (i.e. not threaded) 7/8 inch steel handlebars.

Perfect for achieving that minimal look on your bike

 Availability varies on this part, check availability

Modern solid state electronic regulator for models with Bosch charging system

Bolts to original mounting point but this replacement part is not as tall as the old metal regulator. Also known as Guzzi ref. 17703800. Replaces ELA29704

See our Bosch fault finder page for help diagnosing problems on your Bosch charging system. The original type mechanical regulator is no loger available

 2 in stock

29703800-z 29703800 GU29703800 29 70 38 00
 2970 3800 2970.3800 29.70.38.00

Taper roller bearing, used for front wheel on loop frame models with 2 shoe front drum

2 required for front wheel on loop frame models. Also known as Guzzi ref. 92201421. Rear wheel bearing for loop frames (2 required) and V7 Sport / 750S
See WHA90249 for bearing seal

 This part is due back in stock soon, call 01484 841395 to reserve yours

92246922-z 92246922 GU92246922 92 24 69 22
 9224 6922 9224.6922 92.24.69.22

Pair of ignition points (made up of Guzzi part numbers 14715429 and 14715430)

 3 in stock

 14719800 GU14719800 14 71 98 00
 1471 9800 1471.9800 14.71.98.00

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock