Brand new genuine Valeo starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016
Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

This is a genuine Valeo starter made in the EU- please do not confuse with the cheap Chinese copies that sometimes appear on eBay.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Please note you can get a discount of £30 on this item if you part exchange your existing faulty starter motor. See ELA30837 for less expensive alternative part

 This part is due back in stock soon, call 01484 841395 to reserve yours

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Clutch hub or centre for models with twin clutch plates

Also known as clutch gear

 This part is available by special order, request a quote

 04211600 GU04211600 04 21 16 00
 0421 1600 0421.1600 04.21.16.00

Ducati type alternator stator

300W output, doesn't include rotor / magnet. Also known as Guzzi ref. 30712460

 1 in stock

 37712405 GU37712405 37 71 24 05
 3771 2405 3771.2405 37.71.24.05

Polished aluminium instrument console kit for 80mm instruments (as used on Le Mans 1, 2, T3, V50 etc...). This high quality kit is specially made for Gutsibits and consists of the following parts:

• Polished aluminium clock surround front with 80mm holes for instruments, slotted ignition switch hole and 8mm instrument light holes
• 6 LEDs with chrome bezels (small spade connectors to rear) for indicators, oil, charge system, neutral and high beam warning light
• Polished aluminium instrument surrounds (odometer surround includes hole for reset knob)
• Polished aluminium instrument backs (attach with existing nuts)

Manufactured from 6mm aluminium, this this instrument binnacle will not fatigue with use and is an excellent way to present the standard 80mm Veglia instruments. Bolts to handlebar yoke clamps. NB instruments and ignition switch shown in photo for illustration purposes only.
This is a high quality UK manufactured part made exclusively for Gutsibits, do not confuse with lesser alternatives. These kits are often prepared to order so please allow for a couple of days delay before your order is sent.

NB This kit works with the ignition switch ELA17735, later type switches will not fit into the predrilled ignition switch hole. On models with cable operated remote odometer resets the reset knob will need to be relocated. Check the depth of your instruments before ordering, this kit is intended for 48mm deep instruments with 60mm stud centres

Instruments with 60 degree or similar angle drives to the rear will require you to enlarge cable cutouts in the plates that make up the rear of the kit

 1 in stock

Bosch fuel pump (in-tank type), this is just the fuel pump and does not include the plate that mounts to the fuel tank

 This part is available by special order, request a quote

01107290-z 01107290 GU01107290 01 10 72 90
 0110 7290 0110.7290 01.10.72.90

Complete TRIOM left hand dip (UK spec) headlight unit with bulb

This is no longer available from Guzzi so we've sourced a replacment part that is the correct size and shape. Note this does not have the side mounting lugs that the original headlamp has

 This part is available by special order, request a quote

30740500-z 30740500 GU30740500 30 74 05 00
 3074 0500 3074.0500 30.74.05.00

12 volt coil used on late Guzzis

Sometimes referred to as the 'square coil', two required per bike. See ELA00001 for crimp on HT lead connector

 This part is due back in stock soon, call 01484 841395 to reserve yours

 30716500 GU30716500 30 71 65 00
 3071 6500 3071.6500 30.71.65.00

Polished rocker cover set for square barrel models consisting of 2 x rocker covers

Plain covers without any sensor mount holes

 This part is available by special order, request a quote

 03999540 GU03999540 03 99 95 40
 0399 9540 0399.9540 03.99.95.40

Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models

Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission

 This part is due back in stock soon, call 01484 841395 to reserve yours

Quality replacement fuel pump from Bosch

For models with the fuel pump mounted external to the fuel tank. No longer available new from Guzzi. Also known as Guzzi ref. 29107261 and 29107260

 Availability varies on this part, check availability

 01107231 GU01107231 01 10 72 31
 0110 7231 0110.7231 01.10.72.31