Brembo brake caliper rebuild kit for one P2 F08 (P8) caliper, contains 2 pairs of seals, O ring and 2 M10 bolts

This seal kit is for F08 calipers fitted to front of all these models. Also used on some Triumph Bonnevilles, MZs, Ducati 600 Pantah, 500 Pantah, 500 Sport Desmo, 500 GTV, 650 SL, 750 F1, 750 F1B, 750 Paso, 750 Sport, 900 MHR, 900 SS, 900 S2, 906 Paso, 100 R1, 100 S2 Desmo, Laverda Jota 1000 and Laverda 1200 Anniversary. Brembo ref. 120274110

See BRA10310 for less expensive replica kit

 More than 5 in stock

 14659000 GU14659000 14 65 90 00
 1465 9000 1465.9000 14.65.90.00

Also fits Benelli 354, Benelli Sei, Ducati 250/350/450 Desmo (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)

Dellorto accelerator pump diaphragm for PHF and PHM carbs

Also known as Guzzi ref 075527555

 2 in stock

 14931050 GU14931050 14 93 10 50
 1493 1050 1493.1050 14.93.10.50

Polished adjustable aluminium brake lever for PS 11, PS 13 and PS 16 master cylinders

Also known as Guzzi ref. 10270652. See HAA10850 for lever pivot pin and BRA01630 for span adjustable alternative lever

 1 in stock

30605680-z 30605680 GU30605680 30 60 56 80
 3060 5680 3060.5680 30.60.56.80

Black plastic pillion backrest embossed with 'Moto Guzzi'

Attaches via two 6mm studs

 1 in stock

 03468210 GU03468210 03 46 82 10
 0346 8210 0346.8210 03.46.82.10

10 spline connection sleeve to connect drive box to driveshaft

 This part is due back in stock soon, call 01484 841395 to reserve yours

12327700-z 12327700 GU12327700 12 32 77 00
 1232 7700 1232.7700 12.32.77.00

Full seal kit and gasket set for overhauling the rear drive box

Bearings available separately

 More than 5 in stock

Upper throttle cable for carb models, connects to splitter under tank. One required

We advise you to measure your existing cable before ordering in case you have a non standard set up.

 1 in stock

 30117560 GU30117560 30 11 75 60
 3011 7560 3011.7560 30.11.75.60

Steel intermediate clutch plate

 This part is due back in stock soon, call 01484 841395 to reserve yours

12082300-z 12082300 GU12082300 12 08 23 00
 1208 2300 1208.2300 12.08.23.00

Kit containing two replacement 60cm silicon HT leads, lead ends and 90° plug caps. The leads are suppied as a single double length lead so you can cut it into two leads of the exact required length. Includes crimp on lead ends for standard big twin 12v round coils

Suitable for most models with coils under the tank where the HT lead is not moulded into the ignition coil. We recommend checking what type of plug cap you have and measuring your existing cable run to check this part will fit

 This part is due back in stock soon, call 01484 841395 to reserve yours

Con rod bearing shell 1st oversize -0.254MM

 This part is available by special order, request a quote

 30062001 GU30062001 30 06 20 01
 3006 2001 3006.2001 30.06.20.01