Brakelight switch

Stop light switch also known as Guzzi ref. AP8224192
See FRA98412 for mounting screw

 2 in stock

03749845-z 03749845 GU03749845 03 74 98 45
 0374 9845 0374.9845 03.74.98.45

Stainless M10 x 1.25 steel banjo bolt, coarser thread (1.25) than most brake fittings. See BRA01001 for M10 x 1 banjo bolt for most other brake fittings and models

 2 in stock

Protective spring for brake fluid supply line joining rear fluid reservoir to rear brake master cylinder

 2 in stock

 30665860 GU30665860 30 66 58 60
 3066 5860 3066.5860 30.66.58.60

Front brake master cylinder cap and rubber kit for Brembo PS 13 master cylinder. Check the screw holes in your master cylinder are diagnally opposed (as seen top left and bottom right corners when sitting on bike)

Reservoir cap replaces Guzzi ref. 2B001928

 2 in stock

 03661145 GU03661145 03 66 11 45
 0366 1145 0366.1145 03.66.11.45

Black cover or cap for Stahlbus M6 bleed valve. Prevents contamination of the valve and smartens up your brake caliper

 2 in stock

Rebuild kit for Brembo P32 rear caliper. This is a comprehensive overhaul kit containing replacement dust seals, fluid seals, o ring, bleed nipple, dust cap, washers, brake grease and caliper bolts. One kit required per caliper. Also suitable for some Ducati / Aprilia models.

Caliper seal kit

 2 in stock

Rebuild kit for Grimeca F05 (P5) type calipers with 32mm pistons

This caliper also known as P2 F05N, P32B and P32F.
This seal kit also known as Brembo ref. 120279910, also used on Benelli 504 Sport, 650 Al'Azzura, Ducati 500s, Laverda 500 Montjuich and Zeta (front) and Bimota DB1 and YB4 (rear).

Not suitable for P32 rear calipers fitted to 750T and Nevada 750 (1991-2001) - see BRA01723 for this model.

 2 in stock

Also fits Benelli 504 Sport, Benelli 250 TS, Ducati Pantah 500SL, 650 Al'Azzura, Ducati 500s, Laverda 500 Montjuich and Zeta (front) and Bimota DB1 and YB4

The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.

Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping!

• Completely sealed by O-ring.
• Hydraulic system remains sealed even during the venting process.
• Reliable non-return function on this auto bleed valve, thus one-man operation.
• System has been bled in minutes.
• Wear of the threads in the caliper is prevented (up and screwing down during the bleeding process).
• For all hydraulic systems such as brakes and clutches stahlbus brake bleed valve just replaces the existing vent screw.
• Tested under extreme conditions by TÃœV Rheinland.
  See BRA41652 for bleed valve cover. Fits front calipers only on models listed above.

   2 in stock

  [ CLOSE WINDOW ]
  [ CLOSE WINDOW ]

Brembo pad pin kit for Brembo P4 30/34F calipers fitted to front forks, two pins

Brembo ref. 120394230

 1 in stock

 01659130 GU01659130 01 65 91 30
 0165 9130 0165.9130 01.65.91.30

Bright aluminium finish brake lever, 4 position span adjustment

See HAA10850 for lever pivot pin

 1 in stock

01605630-z 01605630 GU01605630 01 60 56 30
 0160 5630 0160.5630 01.60.56.30

Also fits Aprilia RS250