Shop headings: New Spares | Used Spares | Accessories | Brands
Flywheel, originally intended for dual point and Motoplat ignitions
2-33° of ignition advance. Supercedes V7 loop frame flywheel 12067000 . Weighs 4.2kg
This part is available by special order, request a quote
17067050 GU17067050 17 06 70 50
1706 7050 1706.7050 17.06.70.50
£249.00
INC VAT
£207.50 EX VAT
Replacement clutch plate for single plate RAM clutches
Torque setting for fitting this is 25Nm with a thread locking compound
This part is available by special order, request a quote
£146.00
INC VAT
£121.67 EX VAT
M8 wavy washer
Also known as a crinkle washer
This part is due back in stock soon, call 01484 841395 to reserve yours
£0.30
INC VAT
£0.25 EX VAT
Factory tool for clutch centre gear nut, this is a superior design tool intended for repeated use
Designed to fit the original factory spec nut- this may not fit some aftermarket items. See TOA14651 for cheaper aftermarket tool
This part is available by special order, request a quote
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£70.00
INC VAT
£58.33 EX VAT
Clutch cable for models with Domino switchgear only
We advise you to measure your existing cable before ordering in case you have a non standard set up.
This part is due back in stock soon, call 01484 841395 to reserve yours
28093034-z 28093034 GU28093034 28 09 30 34
2809 3034 2809.3034 28.09.30.34
£16.60
INC VAT
£13.83 EX VAT
Tool for clutch centre gear nut
Half inch socket drive. This is a cheaper aftermarket tool- see TOA14903 for original factory item
This part is due back in stock soon, call 01484 841395 to reserve yours
14912603 GU14912603 14 91 26 03
1491 2603 1491.2603 14.91.26.03
£39.00
INC VAT
£32.50 EX VAT
Splined tool for aligning clutch plates on reassembly, without this clutch alignment tool you risk damaging the intermediate plate. The tool screws into the back of the crankshaft to compress the clutch springs and align the clutch friction plates
Suitable only for later clutch centre spline type (e.g. clutch plate CLA05430). As used by the Gutsibits spanner monkeys on their bikes
This part is due back in stock soon, call 01484 841395 to reserve yours
30906510 GU30906510 30 90 65 10
3090 6510 3090.6510 30.90.65.10
£110.00
INC VAT
£91.67 EX VAT
Complete single disc clutch kit for 5 speed big twins containing flywheel, new deep spline clutch hub, friction plate, spring plate, pressure plate, and flywheel bolts. Suitable for all big twins with either distributor or crankshaft mounted ignition system, not suitable for Digiplex equipped models.
This clutch upgrade has the following advanges over the old two plate clutch:
This part is due back in stock soon, call 01484 841395 to reserve yours
£520.00
INC VAT
£433.33 EX VAT
Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models
Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission
This part is due back in stock soon, call 01484 841395 to reserve yours
£186.50
INC VAT
£155.42 EX VAT
Original type clutch friction plate for big twins
2 plates required per clutch overhaul- thicker side of each plate should face transmission. Also check your intermediate plate 12082300. This has shallower splines than the Spada 3 on plates. These are the best fit if you still have the original shallow spline clutch hub. Also known as Guzzi ref. 12084400
This part is due back in stock soon, call 01484 841395 to reserve yours
28084460-z 28084460 GU28084460 28 08 44 60
2808 4460 2808.4460 28.08.44.60
£52.00
INC VAT
£43.33 EX VAT