33 Results - Page 4 of 4
Used Alternator Cover Plastic ENG18165 Fits 850/1000 ALL Models, Cali 1100, 1100 Sport, Quota 1100, V50, V50 II, V35 I Example photo for illustration only Dimensions: 210mm x 165mm x 50mm Black plastic alternator cover with Moto Guzzi in white text and long black tab on lower edge Sorry this part cannot be shipped to the US or Canada 6 month warranty on this part We need to check whether we have stock of this part, check availability 18001650 GU18001650 18 00 16 50 1800 1650 1800.1650 18.00.16.50 £11.00 INC VAT £9.17 EX VAT Alternator Brush Set ELA17453 Fits Cali 2, T3, 750S, S3, 850T, T4, T5 (Series 1), Convert, G5, 1000 SP, SP II, Le Mans 1, Le Mans 2, Le Mans 3, Le Mans 1000, Mille GT (Series 1), V35, V35C, V35 Florida, Imola 2, V35 TT, V50, Monza, V65, V7 Sport Replacement alternator brushes or brush kit for Bosch alternators Also known as Guzzi ref 17712453 5 in stock 14712453-z 14712453 GU14712453 14 71 24 53 1471 2453 1471.2453 14.71.24.53 Also fits Benelli 900 Sei (Series 2) £10.00 INC VAT £8.33 EX VAT
600W Original Type Charging System Upgrade Bosch Equipped Models ELA00503 Fits Cali 2, T3, 750S, S3, 850T, T4, T5 (Series 1), Convert, G5, 1000 SP, SP II, Le Mans 1, Le Mans 2, Le Mans 3, Le Mans 1000, Mille GT (Series 1), V35, V35C, V35 Florida, Imola 2, V35 TT, V50, Monza, V65, V7 Sport Alternator upgrade kit for Bosch systems containing stator windings, wound rotor and replacement diode board. The superior design alternator has an output up to 300% greater than the original Bosch system. You may wish to fit a plastic alternator spacer ENA18150 if your model does not have one of these already (to improve cooling of the alternator). You will need front crank seal ENA90428 (Bosch seal) if you wish to fit this to a bike with a Saprisa charging system. This kit reuses your existing Bosch regulator and stator plate with brush holder, see ELA29703 for a replacement regulator and ELA17452 for brush holders. - Outputs 600W @5000 RPM
- Supplied with rotor removal tool
- For tapered crankshafts
Banish charging system worries with this kit!
Installation notes: - Remove stator and rotor using the supplied rotor removal tool
- Remove the old stator windings from the stator plate
- Solder in the new stator widing wires to the connection block on the stator plate and reconnect the
- Mount the replacement diode board, this should be protected from the weather but cooled by passing air
- Connect up the system as follows: Terminals U,V and W take the three yellow wires which should be connected to the stator plate block; Y goes to Y on the stator plate; The brown wires go to earth (we recommend using some earth sleeve on these if possible); Red goes to the battery positive terminal; regulator wiring remains as before (D+ to diode board, D- to earth and DF to brush holder)
- Check charge warning light is working (earth DF wire at stator to check bulb function)
- Turn motor over by hand to ensure everything is seated correctly, there should be an air gap between the stator windings amd rotor
Fit alternator cover and spacer This part is available by special order, request a quote £465.00 INC VAT £387.50 EX VAT Page 4 of 4
|