Shop headings: New Spares | Used Spares | Accessories | Brands
33 Results - Page 3 of 4
Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 12 volt coils and can be used to replace points or Bosch electronic ignition on models with Bosch charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.
2 year warranty on Sachse ignition kits
Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. We recommend fitting Dyna coils ELA14101 with this kit. If you wish to combine this kit with uprated charging system ELA00502 you will need to make or source longer studs (M5 x 67mm x 2) for pickup, and longer centre bolt (M8 x 58mm wasted). See ACA50001 for distributor blanking plate if required
1 in stock
£395.00
INC VAT
£329.17 EX VAT
Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.
2 year warranty on Sachse ignition kits
Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165
This part is available by special order, request a quote
£395.00
INC VAT
£329.17 EX VAT
Stainless steel fasteners kit for PHF and PHM carb models with sump extension.This kit contains nuts, bolts and washers for the following: rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike
This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 149 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)
More than 5 in stock
£85.00
INC VAT
£70.83 EX VAT
Stainless steel fasteners kit for PHF and PHM carb models without sump extension.This kit contains nuts, bolts and washers for the following: distributor clamp, rocker covers, timing cover, gearbox bell housing, alternator cover, gearbox rear cover, neutral switch, drive box to swingarm, starter motor, head studs, exhaust flanges, inlet manifolds and sump. Just what you need to brighten up your Guzzi and ensure nuts and bolts don't seize on your bike
This engine bolt kit contains appropriate M6, M8, M10 socket cap and hex head bolts, nuts and washers. 149 pieces. To ensure you can easily release these fasteners in years to come we recommend wiping each fastener with copper grease (OIA11070). You may also require a replacement front engine bolt kit in stainless (SSA14450) or distributor screws (SSA05025 and SSA04008)
More than 5 in stock
£85.00
INC VAT
£70.83 EX VAT
Pair of high quality large bore exhaust header pipes for standard Le Mans exhaust systems. Finished in black and made in Mandello these downpipes have been developed specifically for the Le Mans 1 and 2 and are an excellent choice for bikes that will be ridden
Note that there is no crosspipe joining these downpipes as they are designed to be used with EXA50009. Unfortunately it is not possible to manufacture black painted downpipes with a crossover in front of the alternator due to the production process.
This part is available by special order, request a quote
£250.00
INC VAT
£208.33 EX VAT
M16 stainless steel half nut and washers for front wheel spindle. Includes flat and wavy washer
NB this is a half nut. Can also be used as alternator retaining nut 92603516
More than 5 in stock
92602516-z 92602516 GU92602516 92 60 25 16
9260 2516 9260.2516 92.60.25.16
£8.50
INC VAT
£7.08 EX VAT
Combined regulator rectifier to replace separate items on Bosch equipped models. See our wiring instructions page for help installing this reg/rec.
Supplied with long leads for battery and alternator connection. Female spades for alternator and charge sensing, ring connectors for battery. NB this reg/rec should not be used with a lithium-ion battery
1 in stock
£140.00
INC VAT
£116.67 EX VAT
Rubber grommet for alternator cover top
See ENA14710 if you are looking for alternate part with cable sheath
2 in stock
19007700 GU19007700 19 00 77 00
1900 7700 1900.7700 19.00.77.00
£5.40
INC VAT
£4.50 EX VAT
Rubber sleeve for alternator cover top, can be used instead of ENA19700
This part is due back in stock soon, call 01484 841395 to reserve yours
14710200 GU14710200 14 71 02 00
1471 0200 1471.0200 14.71.02.00
£4.80
INC VAT
£4.00 EX VAT
A2 stainless socket cap screw M5 x 45, used for retaining Bosch alternator stator
More than 5 in stock
98620245 GU98620245 98 62 02 45
9862 0245 9862.0245 98.62.02.45
£1.20
INC VAT
£1.00 EX VAT