This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.

Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.

See installation instructions here.

 1 in stock

Pair of universal Domino chromed handlebars, medium rise.

Not suitable for V65 GT, Mille GT or other models with wide handlebar clamps - see dimensions if in doubt about suitability for your bike

 1 in stock

Shallow splined Newfren clutch friction plate for big twins with old shallow splined clutch centre

2 plates required per clutch overhaul- thicker side of each plate should face transmission. Also check your intermediate plate 12082300. This has shallower splines than the Spada 3 on plates. These are the best fit if you still have the original shallow spline clutch hub

 2 in stock

28084460-z 28084460 GU28084460 28 08 44 60
 2808 4460 2808.4460 28.08.44.60

Pair of engine crash bars finished in tough black. The heads and rocker covers are vulnerable on these bikes and can be badly damaged by even a minor accident, replacement cost can be more than £1000 so protect your bike with these bars.

Supplied with fitting hardware and bracket finished in black, this crashbar has been specially developed for the second generation V7. See our technical documents section for installation instructions. Engine bars - essential protection for your bike.

 1 in stock

Spacer for swinging arm. Two required.

 This part is due back in stock soon, call 01484 841395 to reserve yours

 12547200 GU12547200 12 54 72 00
 1254 7200 1254.7200 12.54.72.00

HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 This part is available by special order, request a quote

HIgh performance aluminium velocity stack for airbox to throttle body union on single throttle body models. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 This part is due back in stock soon, call 01484 841395 to reserve yours

Satin finish Avion performance silencer. Full deep sound enhances the V-twin engine note and you'll appreciate the extra 2hp that is released. It's also a full kilo lighter than the stock part. Distinctive Avion styling and shorter length compliments the V100 Mandello. Includes carbon fibre heat shield.
Mistral focused the development on the technical details that characterize this exhaust, performing something of unique. Thanks to a different internal construction Mistral saved about 1 kilogram compared to the stock silencer and improved performance, not that the bike was lacking but more fluidity and torque is always a good thing to have. The final endcap, totally milled from a block of aluminum, ensure an unique and valuable look that combined with the carbon fibre heat shield match perfectly the sportly character of the bike.

• CNC machined end cap made by Anticorodal
• 1 kg lighter than stock
• 10% more torque off tickover
• Full and deep sound
• Specific heat shield and bracket included
• dB-Killer compliant with EURO5 regulations
• Compatible with the standard factory centre stand
• +2 HP e + 1 Nm (+ 3 HP increase If combined with Racing Air Filter SIA09776 )
• Laser engraved MISTRAL logo

 This part is available by special order, request a quote

Polished finish performance silencer. Full deep sound enhances the v-twin engine note and you'll appreciate the extra 1.5hp that is released. It's also a full kilo lighter than the stock part.

• CNC machined end cap made by Anticorodal
• 1 kg lighter than stock
• 10% more torque off tickover
• Specific heat shield and bracket included
• dB-Killer compliant with EURO5 regulations
• Laser engraved MISTRAL logo

 This part is available by special order, request a quote

Complete chrome indicator with clear lens and wiring lead, includes orange bulb

Fits front left or rear right, plastic stem. Also known as Guzzi ref. 06751600

 This part is due back in stock soon, call 01484 841395 to reserve yours

32751660-z 32751660 GU32751660 32 75 16 60
 3275 1660 3275.1660 32.75.16.60