High performance aluminium velocity stack for airbox to throttle body union on single throttle body models. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 1 in stock

HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434

Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 1 in stock

12 volt single output 3 Ohm ignition coil (lead to distributor)

Push fit HT lead, see ELA00001 for crimp on HT lead connector. Supplied without coil clamp

 This part is due back in stock soon, call 01484 841395 to reserve yours

 26716504 GU26716504 26 71 65 04
 2671 6504 2671.6504 26.71.65.04

Red lens for oblong rear light, includes clear section to illuminate number plate

Can be used to replace tail light lens on Lario and Le Mans 1000, note that this one does not have side 'wings' but is functional on these models

 1 in stock

 65741700 GU65741700 65 74 17 00
 6574 1700 6574.1700 65.74.17.00

Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models

Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission

 This part is due back in stock soon, call 01484 841395 to reserve yours

Pair of short reverse cone stainless steel performance silencers from Mistral, the reverse cone design compliments the classic styling of the V7 models. Supplied with removable DB killer these are a more durable, stylish, lighter and better sounding than the original silencers.

5kg lighter that stock silencers
Increased power

Euro 5 compliant
No remap required
All Mistral exhausts are hand made in Mandello using high quality components, Mistral develop exhausts that get the best performance from your Moto Guzzi.
Supplied with silencer clamps and certificate of homologation, reuse your existing silencer brackets with these silencers.You will also need centre stand stop bracket FRA34373 if you have the Guzzi centre stand fitted.

Silencer shims not required

Release the music in your Guzzi!

 1 in stock

Cartridge oil filter

For an oil change we also recommend 1x ENA01580 (Oil filter cover O ring) and 1 x SIA10900 (small sump drain crush washer).

 This part is due back in stock soon, call 01484 841395 to reserve yours

1A023949

Kit of 8 frame and footpeg caps to finish off your V100. The kit, made of plastic material resistant to UV rays and heat, was developed specifically for the Moto Guzzi V100. It consists of 6 footrest caps and 2 frame caps, covering both the right and left sides. The frame caps are finished with a Moto Guzzi eagle emblem in keeping with the branding elsewhere on the V100. These frame caps tidy the side profile of your machine and prevent water and road spray getting into the frame.

Note that the included M10 washer is required to space the gear lever so it is clear of the installed plugs. We recommend using a small dab of glue during installation of the plugs for security. Scan the QR code on the box for a short video guide to installation.

 This part is due back in stock soon, call 01484 841395 to reserve yours

Satin finish Avion performance silencer. Full deep sound enhances the V-twin engine note and you'll appreciate the extra 2hp that is released. It's also a full kilo lighter than the stock part. Distinctive Avion styling and shorter length compliments the V100 Mandello. Includes carbon fibre heat shield.
Mistral focused the development on the technical details that characterize this exhaust, performing something of unique. Thanks to a different internal construction Mistral saved about 1 kilogram compared to the stock silencer and improved performance, not that the bike was lacking but more fluidity and torque is always a good thing to have. The final endcap, totally milled from a block of aluminum, ensure an unique and valuable look that combined with the carbon fibre heat shield match perfectly the sportly character of the bike.

• CNC machined end cap made by Anticorodal
• 1 kg lighter than stock
• 10% more torque off tickover
• Full and deep sound
• Specific heat shield and bracket included
• dB-Killer compliant with EURO5 regulations
• Compatible with the standard factory centre stand
• +2 HP e + 1 Nm (+ 3 HP increase If combined with Racing Air Filter SIA09776 )
• Laser engraved MISTRAL logo

 This part is available by special order, request a quote

HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM

This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA85433 and V-Twin Boost - ACA85001 or ACA85002.

Customer Kev fitted this combo and called us the next day to say that his V85TT was transformed; the fluffy throttle response between 2k and 3k was gone and the engine pulled better. Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.

 This part is due back in stock soon, call 01484 841395 to reserve yours