Gorgeous polished aluminium reservoir cap for PS15 Brembo master cylinder fitted to rear linked system on many models, will fit front master cylinder on models where a PS15 handlebar master cylinder is fitted. Seal is not included with this cap - you should re-use your original cap seal

Make your Guzzi stand out from the crowd!

 This part is available by special order, request a quote

 14661100 GU14661100 14 66 11 00
 1466 1100 1466.1100 14.66.11.00

Also fits Ducati 600 SL Pantah, Ducati 750/900 SS, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR, Ducati 1000 MHR

Gorgeous polished aluminium reservoir cap for PS12 Brembo master cylinder fitted to front brake on many models, fits rear master cylinder on more recent models

Make your Guzzi stand out from the crowd!

 This part is available by special order, request a quote

 10430830 GU10430830 10 43 08 30
 1043 0830 1043.0830 10.43.08.30

Bare aluminium finish brake lever

 1 in stock

17605652-z 17605652 GU17605652 17 60 56 52
 1760 5652 1760.5652 17.60.56.52

Also fits Laverda

Pair of replacement anodised alloy pistons for Brembo F05 (P5) calipers. These also fit Grimeca calipers with 32mm pistons

Also used on some Laverdas. BRA19301 for alternative part in stainless steel

 This part is due back in stock soon, call 01484 841395 to reserve yours

 19652300 GU19652300 19 65 23 00
 1965 2300 1965.2300 19.65.23.00

Also fits Benelli 250 TS, Ducati Pantah 500SL

Brakelight switch (microswitch) with 2 pin lead

Also see ELA30860

 Availability varies on this part, check availability

 27749815 GU27749815 27 74 98 15
 2774 9815 2774.9815 27.74.98.15

Front right hand brake pipe linking right hand caliper to manifold on front yoke

Original type rubber brakeline with chunky galvanized ends

 This part is available by special order, request a quote

63657121-z 63657121 GU63657121 63 65 71 21
 6365 7121 6365.7121 63.65.71.21

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Polished adjustable aluminium brake lever for PS 11, PS 13 and PS 16 master cylinders

Also known as Guzzi ref. 10270652. See HAA10850 for lever pivot pin and BRA01630 for span adjustable alternative lever

 1 in stock

30605680-z 30605680 GU30605680 30 60 56 80
 3060 5680 3060.5680 30.60.56.80

Brembo brake master cylinder overhaul kit for handlebar, undertank (cable operated) mounted, handlebar mounted and rear PS 12 master cylinders. Contains seals, brake grease, spring and piston. PS12 handlebar master cylinder fitted to early 850 and 1000 models. PS12 rear master cylinder fitted to Nevada 750

This seal kit is also known as 082039797. NB repair kit instructions refer to rear master cylinder. To fit this to a PS12 handlebar mounted cylinder you will need to punch the old piston out using a thin drift through the hole at the banjo bolt end of the master cylinder. Carefully note the order of the ring and washer as the piston comes out and replace with components from kit. Brembo no. 110279720. See this link for help with fitting this kit

 More than 5 in stock

 17659352 GU17659352 17 65 93 52
 1765 9352 1765.9352 17.65.93.52

Also fits Ducati 500 SL Pantah, Ducati 350/500 Twin GTV, Ducati 350/500 SL Pantah, Benelli 500 Quattro, Benelli 504 Sport, Benelli 250 2C, Benelli 900 Sei, Laverda Montjuic, Harris F1

Adjustable front black brake lever for PS 11, PS 13 and PS 16 rectangular master cylinder.

Also known as Guzzi ref. 28605678. See BRA01630 or BRA01640 for a span adjustable alternative and HAA10850 for lever pivot pin

 This part is due back in stock soon, call 01484 841395 to reserve yours

10270640-z 10270640 GU10270640 10 27 06 40
 1027 0640 1027.0640 10.27.06.40