CEV type lights (off/pilot/on), main beam and horn switch. Supplied without wires, you will need to solder your wiring into the switchgear using a minimum 60W soldering iron. Switch fixes to handlebars using included screws

Can be fitted to left or right side of bars

 This part is due back in stock soon, call 01484 841395 to reserve yours

12746001-z 12746001 GU12746001 12 74 60 01
 1274 6001 1274.6001 12.74.60.01

12 volt single output 3 Ohm ignition coil (lead to distributor)

Push fit HT lead, see ELA00001 for crimp on HT lead connector. Supplied without coil clamp

 This part is due back in stock soon, call 01484 841395 to reserve yours

 26716504 GU26716504 26 71 65 04
 2671 6504 2671.6504 26.71.65.04

Prolong battery life with this 9 stage smart battery charger, suitable for 6v, 12v AGM and lead acid batteries.

Weatherproof - suitable for use outside 6V / 12V 1A Auto-sensing charger. Suits all AGM, Lead Acid, Calcium and Gel batteries Charges 6v and 12v batteries Ring terminal and alligator clip harnesses included Spark proof Maintains full charge Simple, connect and wait for green light Overload / Short circuit protection See ACA96001 for a spare set of charging leads (e.g. for a separate bike).

 This part is due back in stock soon, call 01484 841395 to reserve yours

CEV type indicator switch. Supplied without wires, you will need to solder your wiring into the switchgear using a minimum 60W soldering iron. Switch fixes to handlebars using included screws

Can be fitted to left or right side of bars

 This part is due back in stock soon, call 01484 841395 to reserve yours

12750300-z 12750300 GU12750300 12 75 03 00
 1275 0300 1275.0300 12.75.03.00

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 1 in stock

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Neutral indicator switch

 Availability varies on this part, check availability

 12207200 GU12207200 12 20 72 00
 1220 7200 1220.7200 12.20.72.00

Replacement solenoid for original Bosch starter motor.

Note that this solenoid has a bright zinc finsh

 This part is due back in stock soon, call 01484 841395 to reserve yours

 14730554 GU14730554 14 73 05 54
 1473 0554 1473.0554 14.73.05.54

3 position 4 pin ignition switch includes start position

Male spade connectors to rear, supplied with 2 keys

 This part is available by special order, request a quote

 12735300 GU12735300 12 73 53 00
 1273 5300 1273.5300 12.73.53.00

Permanent replacement for unreliable condensers. This capacitor replaces the condenser with a unit that should never need to be replaced

Earths through supplied fitting bracket. Fit and forget reliability

 This part is due back in stock soon, call 01484 841395 to reserve yours

 12715421 GU12715421 12 71 54 21
 1271 5421 1271.5421 12.71.54.21

Old type 4 pin starter relay in metal case. Note that this has two large terminals and two smaller ones, depending on model you may need to fit wider spade connectors to fit this relay. See ELA10003 for large female spade connectors

 This part is due back in stock soon, call 01484 841395 to reserve yours

 12732500 GU12732500 12 73 25 00
 1273 2500 1273.2500 12.73.25.00