Piston ring compressing tool, compresses piston rings to fit into bore. Without this tool you risk snapping piston rings, the tool also speeds up the fitting of new rings

For 57mm - 125mm bores, supplied with hex key for bore adjustment. Not suitable for CARC models

 This part is available by special order, request a quote

Cam follower / tappet, standard size

Not for PI / hydraulic tappet models produced between 2003 and 2006

 2 in stock

 17045860 GU17045860 17 04 58 60
 1704 5860 1704.5860 17.04.58.60

Complete high quality gasket kit for round barrel 850 models

This is only a gasket set, it does not include oil seals and O rings. The top end O rings required are 12 x ENA97624 and 2 x ENA90203

 This part is due back in stock soon, call 01484 841395 to reserve yours

17999050-z 17999050 GU17999050 17 99 90 50
 1799 9050 1799.9050 17.99.90.50

Pair of chrome tubular rocker cover protector bars for round and square barrel engines, these will protect barrels and rocker cover in the unfortunate event of your bike being dropped

These head protectors bolt to the head using existing rocker cover bolts, they won't fit models with fairing lowers that wrap around the cylinders (e.g. Spada) without modification. To modify simply reduce the length of the rear section of the bar to stop short of the fairing and insert the supplied grommet. These bars are supplied with a plastic grommet for each end, this will need chamfering or leaving off on round head models with bolt on rocker cover breather pipes, e.g. T3. These bars will not fit on a T3 or other model with knee pads

 This part is due back in stock soon, call 01484 841395 to reserve yours

Polished aluminium distributor cover for models with points or electronic ignition. Alternative for plastic cover ENA14420

See SSA05025 for the screws which secure this dizzie cap

 1 in stock

14715420-z 14715420 GU14715420 14 71 54 20
 1471 5420 1471.5420 14.71.54.20

Piston ring set

4 ring set

 2 in stock

14060700-z 14060700 GU14060700 14 06 07 00
 1406 0700 1406.0700 14.06.07.00

Complete gasket kit

 This part is available by special order, request a quote

Crankcase breather tank / box in black. Also suitable for round barrelled specials where the standard airbox has been replaced with aftermarket filters

3 pipe connections on underside (large, medium and small diameters), plus connection for rocker cover breather pipes. Connects to ENA14157, ENA17700 and ENA95136

 This part is due back in stock soon, call 01484 841395 to reserve yours

14155700-z 14155700 GU14155700 14 15 57 00
 1415 5700 1415.5700 14.15.57.00

Stainless steel braided hose oil pipes for head to crankcase connection. Replaces leak prone rubber pipes. Includes V shaped banjo.

Always replace crush washers (6 x SIA12200) when fitting new oil lines, you may also require three of our banjo bolts ENA95990

 3 in stock

 14153601 GU14153601 14 15 36 01
 1415 3601 1415.3601 14.15.36.01

Short screw in polished alloy thermometer dipstick with O ring for models without a sump extension. Shows oil temperature in degrees celcius

Supplied unmarked, you will need to mark the rod using a small file to match your existing dipstick

 This part is available by special order, request a quote

17004951-z 17004951 GU17004951 17 00 49 51
 1700 4951 1700.4951 17.00.49.51