Pair of EBC FA047 brake pads for Brembo F05 (P5) calipers and Grimeca front calipers

 5 in stock

27654610-z 27654610 GU27654610 27 65 46 10
 2765 4610 2765.4610 27.65.46.10

Also fits Benelli 250 TS, Ducati Pantah 500SL, Magni Sfida

One litre AGIP brake and clutch fluid, this is a high performance DOT 3 and 4 fluid suitable for all Moto Guzzis

Mixes safely with other DOT 3 , DOT 4 and DOT 5.1 brake and clutch fluids. If you are having problems bleeding your brakes you may need one of our one way bleed nipples BRA41651 and BRA41650

Please note this part CANNOT be posted outside of the UK mainland area.

See BRA99014 for high performance alternative

 More than 5 in stock

Brakelight switch for handlebar mounted master cylinder

Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815 or ELA30860. Sometimes supplied with three terminals, in this instance disregard middle terminal. Please note that terminals are smaller than standard switch and will need to be soldered on.

 1 in stock

 30749860 GU30749860 30 74 98 60
 3074 9860 3074.9860 30.74.98.60

99cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir

Brake fluid, oil and fuel resistant. This is long enough for the rear brake master cylinder on V50 II and V35 I

 More than 5 in stock

Brake pad spring for single pin Brembo Goldline 30/34 calipers

Also suitable for some Ducati / Aprilia models. Brembo ref. 98.8248.50

 1 in stock

 20419685 GU20419685 20 41 96 85
 2041 9685 2041.9685 20.41.96.85

Cover rubber for PS 13 and PS 16 brake master cylinder lever

Brembo ref. 110353040

 This part is available by special order, request a quote

 27663615 GU27663615 27 66 36 15
 2766 3615 2766.3615 27.66.36.15

49cm length of black pipe with clips for connecting rear master cylinder to brake fluid reservoir

Brake fluid, oil and fuel resistant. We recommend measuring your existing pipe first to check ensure this 49cm pipe will be long enough. This is not long enough for the rear brake master cylinder on V50 II and V35 I

 More than 5 in stock

Kit containing 2 stainless steel M10 banjo bolts for Brembo brake fittings with copper washers

Supplied with 4 crush washers. Also known as Guzzi ref. 95990033

 2 in stock

95990028-z 95990028 GU95990028 95 99 00 28
 9599 0028 9599.0028 95.99.00.28

Also fits Laverda Jota

Stainless steel M10 bleed nipple for Brembo single bleed P2 F08 (P8) calipers on pre 1998 models. This is the same length as the genuine Brembo part BRA17659. M10 bleed screw used only on rear of 2003 on models

Part of Guzzi ref. 17659260. Some brake calipers may require a longer bleed screw, we reecommend measuring your existing screw - it should be 15mm from under the flats to the base of the tip.

 5 in stock

Brembo pad pin kit for rear Brembo P32 caliper

Also known as Guzzi ref. 20280030, mostly rear caliper applications. Brembo ref. 120280030

 1 in stock

 30659101 GU30659101 30 65 91 01
 3065 9101 3065.9101 30.65.91.01

Also fits Bimota DB2