Special tool for tightening and untightening the dipstick on small twins. The dipstick can be awkward to undo on these models but this tool makes it simple and quick. No more struggling to grip it or resorting to pliers, just use our tool.
Oil filler tool manufactured from PETG filament these are fully recyclable but as strong as ABS. Dipstick spanner 3D printed in the UK
More than 5 in stock
14927001 GU14927001 14 92 70 01
1492 7001 1492.7001 14.92.70.01
£12.00
INC VAT
£10.00 EX VAT
Sebac fork damper, standard damping rate
Also known as Guzzi ref. 18526460. See OIA01001 for ATF (used in place of fork oil)
4 in stock
14526455-z 14526455 GU14526455 14 52 64 55
1452 6455 1452.6455 14.52.64.55
Also fits Benelli Sei 900
£27.90
INC VAT
£23.25 EX VAT
Dimensions:
55mm x 33mm x 26mm overall
5 pin 12 volt relay suitable for starter, lights, indicator, flasher and horn applications
Supercedes Guzzi ref. 12732500. Equivalent to 28732500 but with mounting bracket
More than 5 in stock
19732500-z 19732500 GU19732500 19 73 25 00
1973 2500 1973.2500 19.73.25.00
£15.20
INC VAT
£12.67 EX VAT
Oil pressure sender
Can also be used in place of oil pressure switch 17768750 and adapter 19055800 on Monza (check which type your small twin uses before replacing). Replaces two part sensor 31999581.
See ENA12640 for replacement crush washer if required
3 in stock
19768720-z 19768720 GU19768720 19 76 87 20
1976 8720 1976.8720 19.76.87.20
£15.50
INC VAT
£12.92 EX VAT
£12.50
INC VAT
£10.42 EX VAT
Dimensions:
310mm - 440mm from fork top
Pair of FAC air assisted fork dampers. These are a major suspension upgrade for the front end of your bike and work best when combined with progressive fork springs SUA18961
Stainless steel damper rod and alloy top nut, supplied with fork top O ring. Pressurise to between 7 and 29 PSI. See OIA01001 for ATF (used in place of fork oil)
1 in stock
14526455-z 14526455 GU14526455 14 52 64 55
1452 6455 1452.6455 14.52.64.55
Also fits Benelli Sei 900
£245.00
INC VAT
£204.17 EX VAT
Dimensions:
Inner length 1100mm, outer length 1005mm
Throttle cable, runs from twistgrip to carb
Ball end at twistgrip
2 in stock
13117565-z 13117565 GU13117565 13 11 75 65
1311 7565 1311.7565 13.11.75.65
£11.00
INC VAT
£9.17 EX VAT
Dimensions:
110mm 50mm x 34mm overall
Riders footpeg rubber, black with chamfered underside
More than 5 in stock
39443200-z 39443200 GU39443200 39 44 32 00
3944 3200 3944.3200 39.44.32.00
£7.00
INC VAT
£5.83 EX VAT
Dimensions:
520mm lead
Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.
Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear
1 in stock
01738030 GU01738030 01 73 80 30
0173 8030 0173.8030 01.73.80.30
£88.00
INC VAT
£73.33 EX VAT
Dimensions:
220mm outer length, 93mm free length, 2.7mm barrel nipple, 2.7mm barrel nipple
Lower right hand choke cable for carb models
We advise you to measure your existing cable before ordering in case you have a non standard set up.
3 in stock
30133560 GU30133560 30 13 35 60
3013 3560 3013.3560 30.13.35.60
£6.60
INC VAT
£5.50 EX VAT
Secure online shopping 
