Dimensions:
50mm x 34mm overall
Riders footpeg rubber, black with chamfered underside
More than 5 in stock
39443200-z 39443200 GU39443200 39 44 32 00
3944 3200 3944.3200 39.44.32.00
£7.00
INC VAT
£5.83 EX VAT
Dimensions:
520mm lead
Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.
Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear
1 in stock
01738030 GU01738030 01 73 80 30
0173 8030 0173.8030 01.73.80.30
£88.00
INC VAT
£73.33 EX VAT
Dimensions:
7mm ID x 12mm OD x 990mm
Oil return pipe with threaded union for sump
Can be used in place of GU32159310 on late V7 models if pipe is cut and breather valve from old pipe inserted into cut section.
Uses crush washer SIA12200
4 in stock
27159360-z 27159360 GU27159360 27 15 93 60
2715 9360 2715.9360 27.15.93.60
£13.20
INC VAT
£11.00 EX VAT
Dimensions:
54mm internal diameter (small end), 70mm diameter (big end) x 40mm
Black rubber UJ gaiter / boot, clips available separately - see SSA64990 and TRA12544
More than 5 in stock
18548000 GU18548000 18 54 80 00
1854 8000 1854.8000 18.54.80.00
£12.50
INC VAT
£10.42 EX VAT
Dimensions:
20mm x 6mm x 9mm excluding spade connectors
Brakelight switch for handlebar mounted master cylinder
Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815. See ELA30861 for less expensive alternative part. Sometimes supplied with three terminals, in this instance disregard middle terminal
4 in stock
30749860 GU30749860 30 74 98 60
3074 9860 3074.9860 30.74.98.60
£17.60
INC VAT
£14.67 EX VAT
Dimensions:
38mm ID x 44mm OD x 26mm
Exhaust gasket, silencer bush or muffler gasket shim for exhaust joint between silencer and downpipe
2 exhaust bushes required per bike
More than 5 in stock
91113826 GU91113826 91 11 38 26
9111 3826 9111.3826 91.11.38.26
£15.00
INC VAT
£12.50 EX VAT
Dimensions:
220mm outer length, 93mm free length, 2.7mm barrel nipple, 2.7mm barrel nipple
Lower right hand choke cable for carb models
We advise you to measure your existing cable before ordering in case you have a non standard set up.
3 in stock
30133560 GU30133560 30 13 35 60
3013 3560 3013.3560 30.13.35.60
£6.60
INC VAT
£5.50 EX VAT
Dimensions:
38mm diameter x 97mm x 20mm ID
Footrest rubber, lattice patterned
Used for pillion and / or riders footrest depending on model. NB some T3 models use FRA14443 for pillion footrest rubber, check your bike before ordering
More than 5 in stock
14443200-z 14443200 GU14443200 14 44 32 00
1444 3200 1444.3200 14.44.32.00
£15.00
INC VAT
£12.50 EX VAT
Dimensions:
95mm x 43mm x 40m overall. Peg hole diameter 19mm
Riders footpeg rubber, black with chamfered underside
4 in stock
28443201-z 28443201 GU28443201 28 44 32 01
2844 3201 2844.3201 28.44.32.01
£7.60
INC VAT
£6.33 EX VAT
Dimensions:
480mm overall pipe length
Cylinder head breather pipe, head to breather box/airbox
Banjo connection at head, push fit to airbox/breather box, see ENA95990 for banjo bolt
More than 5 in stock
17159700-z 17159700 GU17159700 17 15 97 00
1715 9700 1715.9700 17.15.97.00
£13.00
INC VAT
£10.83 EX VAT
Secure online shopping 
