Bright aluminium finish brake lever, 4 position span adjustment

See HAA10850 for lever pivot pin

 1 in stock

01605630-z 01605630 GU01605630 01 60 56 30
 0160 5630 0160.5630 01.60.56.30

Also fits Aprilia RS250

Fine thread screw in brakelight switch for linked system proportioning valve or splitter. See ELA12735 for rubber cap

Stop light switch also known as Guzzi ref. 63657000

 5 in stock

 79654116 GU79654116 79 65 41 16
 7965 4116 7965.4116 79.65.41.16

Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 GT/Sport Köwe, Ducati 750 Paso (1984-1992), Ducati 750 Sport, Ducati 750/900 SS Köwe, Ducati 750 F1/Laguna Seca, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR-I, Ducati 900 SS (1990), Ducati 906 Paso (1988), Ducati 1000 MHR-2/S2

Oil pressure sender, M12 thread, male bullet connector

Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.

See ENA12640 for replacement crush washer if required

 More than 5 in stock

 17768750 GU17768750 17 76 87 50
 1776 8750 1776.8750 17.76.87.50

NGK CPR8EB-9 spark plug

See TOA05931 for spark plug spanner

 More than 5 in stock

 887481 MG887481

Riders footpeg rubber, black with chamfered underside

 More than 5 in stock

39443200-z 39443200 GU39443200 39 44 32 00
 3944 3200 3944.3200 39.44.32.00

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 12 volt coils and can be used to replace points or Bosch electronic ignition on models with Bosch charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. We recommend fitting Dyna coils ELA14101 with this kit. If you wish to combine this kit with uprated charging system ELA00502 you will need to make or source longer studs (M5 x 67mm x 2) for pickup, and longer centre bolt (M8 x 58mm wasted). See ACA50001 for distributor blanking plate if required

 1 in stock

Swingarm bearing oil seal

Dust seal for swingarm bearing

 More than 5 in stock

 90403040 GU90403040 90 40 30 40
 9040 3040 9040.3040 90.40.30.40

Exhaust gasket, silencer bush or muffler gasket shim for exhaust joint between silencer and downpipe

2 exhaust bushes required per bike

 More than 5 in stock

 91113826 GU91113826 91 11 38 26
 9111 3826 9111.3826 91.11.38.26

Fine thread screw in brakelight switch for linked system proportioning valve or splitter. See ELA12735 for rubber cap

Stop light switch also known as Guzzi ref. 63657000

 5 in stock

 79654116 GU79654116 79 65 41 16
 7965 4116 7965.4116 79.65.41.16

Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 GT/Sport Köwe, Ducati 750 Paso (1984-1992), Ducati 750 Sport, Ducati 750/900 SS Köwe, Ducati 750 F1/Laguna Seca, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR-I, Ducati 900 SS (1990), Ducati 906 Paso (1988), Ducati 1000 MHR-2/S2

Output oil seal for drive box

This oil seal fits output side of bevel box

 More than 5 in stock

90407085-z 90407085 GU90407085 90 40 70 85
 9040 7085 9040.7085 90.40.70.85