Metal bush for foot brake or gear lever pivot
4 in stock
30678160 GU30678160 30 67 81 60
3067 8160 3067.8160 30.67.81.60
£15.00
INC VAT
£12.50 EX VAT
Dellorto 260 needle jet or atomiser for VHB24 and VHB26 carbs
2 in stock
19935501 GU19935501 19 93 55 01
1993 5501 1993.5501 19.93.55.01
£15.00
INC VAT
£12.50 EX VAT
Updated bush with thicker rubber section for front of torque arm / cardan arm / reaction rod on CARC models
1 in stock
883045 MG883045
£28.00
INC VAT
£23.33 EX VAT
Speedo sensor with lead and 3 pin plug
Also known as Guzzi ref. 06765400. There are several variants of these sensors, please compare to the sensor on your bike or contact us with a chassis number before ordering
1 in stock
883768 MG883768
£62.00
INC VAT
£51.67 EX VAT
New type clutch friction plate for models with deep splines with deep splined centre
2 plates required- thicker side of each friction plate should face transmission.
Also known as Guzzi ref. 30084410, 03084400, 29084450
V11 Tenni, Rosso Mandello and Scura have a single plate clutch which uses a different friction plate (unfortunately out of production)
These can be fitted to earlier 850 and 1000 models if the early shallow splined clutch centre is replaced with the later deep splined type. See our kit CLA20302 to update early 850/1000 models. Clutch plate alignment tool also available, see TOA30510
More than 5 in stock
05084430 GU05084430 05 08 44 30
0508 4430 0508.4430 05.08.44.30
£57.70
INC VAT
£48.08 EX VAT
Pair of Wirth progressive fork springs
These progressive fork springs improve ride quality and handling by responding progressively to the road. The more the spring is compressed the harder it becomes preventing the forks from bottoming out. See OIA01001 for fork oil
1 in stock
14526600 GU14526600 14 52 66 00
1452 6600 1452.6600 14.52.66.00
Also fits Benelli Sei 750, Benelli Sei 900, Honda CB450 K1-5, CB500 K, CB500 4, Kawasaki KZ650 B/C, KH500, 750H, Z750, Z1000A1, Laverda 1000 RGS, Norton Commando, Yamaha RD250, RD350, XS650, TX750
£130.00
INC VAT
£108.33 EX VAT
8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump
See ENA90948 for the oil filter cover o ring
More than 5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£10.00
INC VAT
£8.33 EX VAT
Marelli condenser with cable and mount bracket
2 required
More than 5 in stock
14715433 GU14715433 14 71 54 33
1471 5433 1471.5433 14.71.54.33
£10.50
INC VAT
£8.75 EX VAT
New type clutch friction plate for models with deep splines with deep splined centre
2 plates required- thicker side of each friction plate should face transmission.
Also known as Guzzi ref. 30084410, 03084400, 29084450
V11 Tenni, Rosso Mandello and Scura have a single plate clutch which uses a different friction plate (unfortunately out of production)
These can be fitted to earlier 850 and 1000 models if the early shallow splined clutch centre is replaced with the later deep splined type. See our kit CLA20302 to update early 850/1000 models. Clutch plate alignment tool also available, see TOA30510
More than 5 in stock
05084430 GU05084430 05 08 44 30
0508 4430 0508.4430 05.08.44.30
£57.70
INC VAT
£48.08 EX VAT
Oil pressure sender
Can also be used in place of oil pressure switch 17768750 and adapter 19055800 on Monza (check which type your small twin uses before replacing). Replaces two part sensor 31999581.
See ENA12640 for replacement crush washer if required
4 in stock
19768720-z 19768720 GU19768720 19 76 87 20
1976 8720 1976.8720 19.76.87.20
£15.50
INC VAT
£12.92 EX VAT