Dimensions:
62mm x 27mm x 44mm
Dellorto 8.5g float with tang for needle valve
Most Guzzi big twins originally had 10g floats- see FUA14001
3 in stock
14933000 GU14933000 14 93 30 00
1493 3000 1493.3000 14.93.30.00
£22.50
INC VAT
£18.75 EX VAT
Dimensions:
310mm tall x 325mm wide
Standard grey tinted screen for headlamp fairing. Includes screen edge trim.
Fitting kits available separately. Screen fasteners are FAA98417 x 3, FAA04001 x 6, FAA90035 x 3, FAA92104 x 3
2 in stock
14577250-z 14577250 GU14577250 14 57 72 50
1457 7250 1457.7250 14.57.72.50
£54.00
INC VAT
£45.00 EX VAT
Dimensions:
13mm ID, 22mm across flats
Gearbox locknut, one nut fitted to each end of the layshaft
1 in stock
10054100 GU10054100 10 05 41 00
1005 4100 1005.4100 10.05.41.00
£11.50
INC VAT
£9.58 EX VAT
Dimensions:
narrow end 50mm ID, wide end 65mm ID x 40mm long
Black rubber UJ boot / gaiter
See TRA23101 for clip
2 in stock
23548080-z 23548080 GU23548080 23 54 80 80
2354 8080 2354.8080 23.54.80.80
£14.00
INC VAT
£11.67 EX VAT
Dimensions:
Inner length 1000mm, 915mm outer length,
Throttle cable from Handlebar splitter to carb, one cable per carb. For models with standard high top PHF pumper carbs.
Only suitable for 1988 on Le Mans 4 & 5 models. We advise you to measure your existing cable before ordering in case you have a non standard set up.
3 in stock
28117778 GU28117778 28 11 77 78
2811 7778 2811.7778 28.11.77.78
£14.00
INC VAT
£11.67 EX VAT
Dimensions:
55mm slider diameter, 195mm between stanchion centres
Tarozzi fork brace, this will help prevent forks twisting under heavy cornering and is a good handling upgrade for older bikes.
1 in stock
Sorry this item is out of production
Lever peg for Tarozzi rearset brake and gear levers. Accepts black rubber ACA11601
M8 threaded mounting
2 in stock
£8.70
INC VAT
£7.25 EX VAT
Dimensions:
62mm OD (small end), 80mm OD (large end)
Black rubber UJ gaiter / boot, clips available separately
Also known as 883966
See TRA93304 for securing clips
1 in stock
05548030 GU05548030 05 54 80 30
0554 8030 0554.8030 05.54.80.30
£19.00
INC VAT
£15.83 EX VAT
Dimensions:
10mm threaded shank, 8mm across flats
A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple
Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap
More than 5 in stock
Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,
£8.00
INC VAT
£6.67 EX VAT
Dimensions:
100cm
One metre of copper core HT lead, this is superior to the more commonly available carbon core lead
Sold by the metre, one metre is enough for two leads on most models with coils under the fuel tank. For models with coils under the side panel you will need two metres. See ELA14715 and ELA14714 for plug caps and ELA20001 for coil screw cap. See ELA00001 for crimp on HT lead connector
More than 5 in stock
£7.00
INC VAT
£5.83 EX VAT
Secure online shopping 
