Dimensions:
38mm x 50 mm x 7mm
Rotational oil seal for crownwheel carrier in drive box on post 1974 big twins. Front crank oil seal on loop frame models
Also known as Guzzi ref. 90403850 and used on 850 GT and loop frame models for front crank oil seal ( 90403851 )
More than 5 in stock
90413850 GU90413850 90 41 38 50
9041 3850 9041.3850 90.41.38.50
£9.80
INC VAT
£8.17 EX VAT
Dimensions:
For 16mm threaded spigot
Cartridge oil filter UFI 23 149 00
Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.
You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket).
Please note that Daytona RS and T5 Polizia use filter SIA15300
More than 5 in stock
14153000 GU14153000 14 15 30 00
1415 3000 1415.3000 14.15.30.00
£10.50
INC VAT
£8.75 EX VAT
Dimensions:
32mm external diameter x 542mm
Chromed fork stanchion
2 in stock
39525401-z 39525401 GU39525401 39 52 54 01
3952 5401 3952.5401 39.52.54.01
Also fits Benelli 504
£105.00
INC VAT
£87.50 EX VAT
Dimensions:
62mm x 27mm x 44mm
Dellorto 8.5g float with tang for needle valve
Most Guzzi big twins originally had 10g floats- see FUA14001
3 in stock
14933000 GU14933000 14 93 30 00
1493 3000 1493.3000 14.93.30.00
£22.50
INC VAT
£18.75 EX VAT
Dimensions:
310mm tall x 325mm wide
Standard grey tinted screen for headlamp fairing. Includes screen edge trim.
Fitting kits available separately. Screen fasteners are FAA98417 x 3, FAA04001 x 6, FAA90035 x 3, FAA92104 x 3
2 in stock
14577250-z 14577250 GU14577250 14 57 72 50
1457 7250 1457.7250 14.57.72.50
£54.00
INC VAT
£45.00 EX VAT
Dimensions:
13mm ID, 22mm across flats
Gearbox locknut, one nut fitted to each end of the layshaft
1 in stock
10054100 GU10054100 10 05 41 00
1005 4100 1005.4100 10.05.41.00
£11.50
INC VAT
£9.58 EX VAT
Dimensions:
narrow end 50mm ID, wide end 65mm ID x 40mm long
Black rubber UJ boot / gaiter
See TRA23101 for clip
2 in stock
23548080-z 23548080 GU23548080 23 54 80 80
2354 8080 2354.8080 23.54.80.80
£14.00
INC VAT
£11.67 EX VAT
Dimensions:
Inner length 1000mm, 915mm outer length,
Throttle cable from Handlebar splitter to carb, one cable per carb. For models with standard high top PHF pumper carbs.
Only suitable for 1988 on Le Mans 4 & 5 models. We advise you to measure your existing cable before ordering in case you have a non standard set up.
3 in stock
28117778 GU28117778 28 11 77 78
2811 7778 2811.7778 28.11.77.78
£14.00
INC VAT
£11.67 EX VAT
Dimensions:
55mm slider diameter, 195mm between stanchion centres
Tarozzi fork brace, this will help prevent forks twisting under heavy cornering and is a good handling upgrade for older bikes.
1 in stock
Sorry this item is out of production
Lever peg for Tarozzi rearset brake and gear levers. Accepts black rubber ACA11601
M8 threaded mounting
2 in stock
£8.70
INC VAT
£7.25 EX VAT
Secure online shopping 
