Manual square bodied fuel tap with nut, washer and filter. Fits left or right hand side of tank.

Off, on and reserve positions. Approved for use with fuel containing ethanol.

 2 in stock

14105400-z 14105400 GU14105400 14 10 54 00
 1410 5400 1410.5400 14.10.54.00

This adjustable fuelling modifier uses the lambda sensor signal to the ECU. By modifying that signal it achieves an improvement in low and midrange throttle response. Comes with wiring harness and instruction manual, installation is simple and does not require any specialist tools. Suitable for all single throttle body V7, V9 and V85 TT models.

Rapid Bike EASY: A base level simple plug and play modulator equipped with a microprocessor managing the lambda sensor signal to optimize the air/fuel ratio, improve the engine efficiency and eliminate power gaps typical of the low and medium rpm range.

See installation instructions here.

 This part is available by special order, request a quote

Pair of EBC FA047 sintered brake pads for Brembo F05 (P5) and Grimeca calipers for extra braking power

Fits Nevada up until frame no. LK112433 Fits all calipers on pre 1993 models

 2 in stock

27654610-z 27654610 GU27654610 27 65 46 10
 2765 4610 2765.4610 27.65.46.10

Also fits Benelli 250 TS

Front crank oil seal for models with Bosch or Ducati charging systems

Also known as Guzz ref. 90402839

 More than 5 in stock

90402840-Z

Stainless steel braided hose oil pipes for head to crankcase connection. Replaces leak prone rubber pipes. Includes V shaped banjo.

Always replace crush washers (6 x SIA12200) when fitting new oil lines, you may also require three of our banjo bolts ENA95990

 1 in stock

 14153601 GU14153601 14 15 36 01
 1415 3601 1415.3601 14.15.36.01

Lower Throttle cable

This runs from the splitter to the carb. We advise you to measure your existing cable before ordering in case you have a non standard set up.

 Sorry, this part is no longer available.

 31117715 GU31117715 31 11 77 15
 3111 7715 3111.7715 31.11.77.15

Smarten up the rear of your V7 with this fenda eliminator kit with includes an LED tail light.

This tail tidy is part of the exciting range of MAS parts to make your V7 stand out from the crowd. Please note that these items are custom made in Italy and normally available to special order with a delivery time of approximately 6 weeks

 2 in stock

Full workshop manual for Cali EV models covering maintenance, overhaul and detailed repair

Includes tolerances for many parts. This is a bound reprint in English which also covers models equipped with hydraulic tappets (PI models)

 Order now and we will post your order within 7 days.

Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models

Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission

 1 in stock

UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 More than 5 in stock

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85