Pair of YSS shocks with 30 position adjustable compression and rebound damping. Variable preload adjustment and 5mm of length adjustment on damper rod.

These are a quality rebuildable rear shock absorber upgrade for all riding conditions. An excellent replacement for tired IKON and KONI Dial-a-Ride shocks

 This part is available by special order, request a quote

Alternator upgrade kit for Bosch systems containing stator windings, wound rotor and replacement diode board. The superior design alternator has an output up to 300% greater than the original Bosch system. You may wish to fit a plastic alternator spacer ENA18150 if your model does not have one of these already (to improve cooling of the alternator). You will need front crank seal ENA90428 (Bosch seal) if you wish to fit this to a bike with a Saprisa charging system. This kit reuses your existing Bosch regulator and stator plate with brush holder, see ELA29703 for a replacement regulator and ELA17452 for brush holders.

• Outputs 600W @5000 RPM
• Supplied with rotor removal tool
• For tapered crankshafts

1. Remove stator and rotor using the supplied rotor removal tool
2. Remove the old stator windings from the stator plate
3. Solder in the new stator widing wires to the connection block on the stator plate and reconnect the
4. Mount the replacement diode board, this should be protected from the weather but cooled by passing air
5. Connect up the system as follows: Terminals U,V and W take the three yellow wires which should be connected to the stator plate block; Y goes to Y on the stator plate; The brown wires go to earth (we recommend using some earth sleeve on these if possible); Red goes to the battery positive terminal; regulator wiring remains as before (D+ to diode board, D- to earth and DF to brush holder)
6. Check charge warning light is working (earth DF wire at stator to check bulb function)
7. Turn motor over by hand to ensure everything is seated correctly, there should be an air gap between the stator windings amd rotor
Fit alternator cover and spacer

 This part is available by special order, request a quote

Pair of YSS shocks with 30 position adjustable compression and rebound damping. Variable preload adjustment and 5mm of length adjustment on damper rod.

These are a quality rebuildable rear shock absorber upgrade for all riding conditions.

 This part is available by special order, request a quote

Pair of YSS shocks with 30 position adjustable compression and rebound damping. Variable preload adjustment and 5mm of length adjustment on damper rod.

These are a quality rebuildable rear shock absorber upgrade for all riding conditions.

 This part is available by special order, request a quote

Complete chromed Hepco and Becker rear luggage rack and pannier rails for Hepco and Becker panniers

 This part is available by special order, request a quote

Complete chromed Hepco and Becker rear luggage rack and pannier rails for Hepco and Becker panniers

 This part is available by special order, request a quote

Complete chromed Hepco and Becker rear luggage rack and pannier rails for Hepco and Becker panniers

 This part is available by special order, request a quote

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 12 volt coils and can be used to replace points or Bosch electronic ignition on models with Bosch charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. We recommend fitting Dyna coils ELA14101 with this kit. If you wish to combine this kit with uprated charging system ELA00502 you will need to make or source longer studs (M5 x 67mm x 2) for pickup, and longer centre bolt (M8 x 58mm wasted). See ACA50001 for distributor blanking plate if required

 1 in stock

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 3 Ohm 12 volt coils and can be used to replace points or Motoplat ignition on models with Saprisa charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA31165

 This part is available by special order, request a quote

Tough Xplorer top box / top case to match Hepco and Becker Xplorer panniers, ideal for enduro touring. Extremely endurable combination of black anodised aluminium sheet and coloured shock-resistant plastic.

• Completely waterproof thanks to special seals
• Made of 1.5 mm thick plate aluminum and highly
impact-resistant plastic molding
• Absorbs impacts and ground contact
• Stable metal locks, integrated carrying handles
• Case and top case available with simultaneous
locking (please specify when ordering)
• Takes a full-face helmet
• Innovative side hinged design
• Fits all H&B rear racks and aluminum racks

 This part is available by special order, request a quote