Sebac fork damper, standard damping rate
Also known as Guzzi ref. 18526460. See OIA01001 for ATF (used in place of fork oil)
This part is due back in stock soon, call 01484 841395 to reserve yours
14526455-z 14526455 GU14526455 14 52 64 55
1452 6455 1452.6455 14.52.64.55
Also fits Benelli Sei 900
£29.00
INC VAT
£24.17 EX VAT
Manually operated fuel tap or fuel valve. Operated by turning base of tap. Supplied with nut and sealing washer
Can be used to replace electronic fuel solenoid valve 03105300 and manual fuel tap 29105460
This part is due back in stock soon, call 01484 841395 to reserve yours
01105460 GU01105460 01 10 54 60
0110 5460 0110.5460 01.10.54.60
£28.00
INC VAT
£23.33 EX VAT
High performance aluminium velocity stack for airbox to throttle body union on single throttle body models. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM
This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434
Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.
1 in stock
£140.00
INC VAT
£116.67 EX VAT
HIgh performance aluminium velocity stack for airbox to throttle body union. This velocity stack replaces the standard part with an aluminium part that protrudes into the airbox. Through careful design it improves the engine response by providing an increased volume of less turbulent air to the throttle body. No modifications are required to fit this velocity stack but you should see a torque increase of around 6% at 2500 RPM and 3% increase in power at 6500 RPM
This manifold is suitable for EURO 4 and 5 models, manufactured on the shores of Lake Como. Developed for optimum power and torque on Mistral's rolling road. For best results combine with a performance air filter - SIA10434
Simple to fit, installation time is less than 30 minutes and the battery does not need to be disconnected.
1 in stock
£150.00
INC VAT
£125.00 EX VAT
12 volt single output 3 Ohm ignition coil (lead to distributor)
Push fit HT lead, see ELA00001 for crimp on HT lead connector. Supplied without coil clamp
This part is due back in stock soon, call 01484 841395 to reserve yours
26716504 GU26716504 26 71 65 04
2671 6504 2671.6504 26.71.65.04
£58.00
INC VAT
£48.33 EX VAT
Red lens for oblong rear light, includes clear section to illuminate number plate
Can be used to replace tail light lens on Lario and Le Mans 1000, note that this one does not have side 'wings' but is functional on these models
1 in stock
65741700 GU65741700 65 74 17 00
6574 1700 6574.1700 65.74.17.00
£14.50
INC VAT
£12.08 EX VAT
Clutch plate kit consisting of 2 x friction plates, 1 x intermediate plate, deep splined clutch centre / boss and tabbed lock washer (not shown). For models with the early type shallow spline plates this is a worthwhile upgrade kit to the better deep splined centre and plates. Clutch plate alignment tool also available, see TOA30510. Suitable for all 5 speed dual plate clutch models
Save £20 on the cost of these components if bought seperately. Does not include clutch springs (see CLA13100). Thicker side of each friction plate should face transmission
This part is due back in stock soon, call 01484 841395 to reserve yours
£186.50
INC VAT
£155.42 EX VAT
Pair of short reverse cone stainless steel performance silencers from Mistral, the reverse cone design compliments the classic styling of the V7 models. Supplied with removable DB killer these are a more durable, stylish, lighter and better sounding than the original silencers.
5kg lighter that stock silencers
Increased power
Euro 5 compliant
No remap required
All Mistral exhausts are hand made in Mandello using high quality components, Mistral develop exhausts that get the best performance from your Moto Guzzi.
Supplied with silencer clamps and certificate of homologation, reuse your existing silencer brackets with these silencers.You will also need centre stand stop bracket FRA34373 if you have the Guzzi centre stand fitted.
Silencer shims not required
Release the music in your Guzzi!
1 in stock
£750.00
INC VAT
£625.00 EX VAT
Cartridge oil filter
For an oil change we also recommend 1x ENA01580 (Oil filter cover O ring) and 1 x SIA10900 (small sump drain crush washer).
This part is due back in stock soon, call 01484 841395 to reserve yours
1A023949
£18.00
INC VAT
£15.00 EX VAT
Kit of 8 frame and footpeg caps to finish off your V100. The kit, made of plastic material resistant to UV rays and heat, was developed specifically for the Moto Guzzi V100. It consists of 6 footrest caps and 2 frame caps, covering both the right and left sides. The frame caps are finished with a Moto Guzzi eagle emblem in keeping with the branding elsewhere on the V100. These frame caps tidy the side profile of your machine and prevent water and road spray getting into the frame.
Note that the included M10 washer is required to space the gear lever so it is clear of the installed plugs. We recommend using a small dab of glue during installation of the plugs for security. Scan the QR code on the box for a short video guide to installation.
This part is due back in stock soon, call 01484 841395 to reserve yours
£26.00
INC VAT
£21.67 EX VAT