Insulated medium female bullet connector

Crimp type

 More than 5 in stock

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with 12 volt 3 Ohm coils ELA14500 (big twins) and can be used to replace Digiplex on models with Ducati charging systems where the bike is converted to carburettors. This kit is just an ignition system, it will not control fuelling. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Once fitted no further adjustment should be necessary. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. See this link for fitting instructions. Some bikes may need at least one additional spacer to allow enough clearance for alternator cover to fit once pickup is fitted. Note that if you are replacing a Digiplex system you will also need to replace your 'square' coils with higher impedance 12 volt coils e.g. ELA14500

 This part is available by special order, request a quote

Complete electronic ignition kit containing alternator mounted ignition pickup, fittings and amplifier unit. Works with standard 12 volt coils and can be used to replace points or Bosch electronic ignition on models with Bosch charging systems. The pickups for this kit are mounted on the alternator stator. Supplied with instructions in German with wiring diagrams.

2 year warranty on Sachse ignition kits

Eliminates vague timing due to worn distributors on big twins. Preloaded with nine ignition curves, two of which are designed for twin plugged bikes. Once fitted no further adjustment should be necessary. See this link for fitting instructions. We recommend fitting Dyna coils ELA14101 with this kit. If you wish to combine this kit with uprated charging system ELA00502 you will need to make or source longer studs (M5 x 67mm x 2) for pickup, and longer centre bolt (M8 x 58mm wasted). See ACA50001 for distributor blanking plate if required

 This part is due back in stock soon, call 01484 841395 to reserve yours

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 This part is due back in stock soon, call 01484 841395 to reserve yours

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Black Magneti Marelli plastic distributor cover for models with points or most electronic ignitions (not Piranha)

See SSA05025 for the screws which secure this dizzie cap

Sorry this part cannot be shipped to the US or Canada

6 month warranty on this part

 6 in stock

 14715420 GU14715420 14 71 54 20
 1471 5420 1471.5420 14.71.54.20

Black Magneti Marelli plastic distributor cover for models with points or most electronic ignitions (not Piranha)

See SSA05025 for the screws which secure this dizzie cap

 1 in stock

 14715420 GU14715420 14 71 54 20
 1471 5420 1471.5420 14.71.54.20

Dizzie bearing

 1 in stock

Coil clamp for round 12 volt coils

2 required per bike. No longer available new, call us to order used coil clamps

 Sorry, this part is no longer available.

Self adhesive cable tie block for securing cables to bodywork and panels, particularly useful where cables must be kept out of the way under the rear mudguard. Simply stick block to bodywork, route cable tie through bracket on block and round wiring

Wiring clip. One block

 More than 5 in stock

Halogen headlight bulb H1 12V 55W. Used for main beam.

Also known as Guzzi ref. 30530557

 1 in stock

 580141 MG580141