The Moto Guzzi Spares Service

Shop headings: New Spares | Used Spares | Accessories | Brands

New Spares Recently Back In Stock

Sort by Title

Sort by Price

Page 12 of 28

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28

Oil Pressure Switch

ELA19670 Fits 850/1000 ALL Models, 1100 Sport ALL, Cali 1100 (1994-1997), Cali EV, Cali Stone, Cali Jackal, Cali Vintage, Centauro, Daytona, Quota 1100, V11 Sport ALL, V35 ALL, V50 ALL, V7 Sport, S3, 750S, V7 700, 850 GT, Nuovo Falcone

Dimensions:
M12 thread, 46mm x 21mm bolt flats

Oil pressure sender, M12 thread, male bullet connector

Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.

See ENA12640 for replacement crush washer if required

part in stock More than 5 in stock

17768750 GU17768750 17 76 87 50
1776 8750 1776.8750 17.76.87.50

£10.00

INC VAT

£8.33 EX VAT this is the price you will pay if you are ordering from outside the UK

Sump Gasket Lower

ENA01360 Fits 1100 Sport IE, Centauro, Daytona RS, V11 Sport, MGS-01

Dimensions:
305mm x 270mm overall

Lower Gasket for oil sump flange

See ENA14036 for upper sump flange gasket

part in stock More than 5 in stock

01003600-z 01003600 GU01003600 01 00 36 00
0100 3600 0100.3600 01.00.36.00

£8.00

INC VAT

£6.67 EX VAT this is the price you will pay if you are ordering from outside the UK

Crank Oil Seal Rear

ENA90367 Fits V7 Sport, 750 S3, 750S, V7 700, V7 Special (1969-1971), 850 GT, 850/1000 All Models, 1100 Sport ALL, 1200 Sport, Centauro, Daytona, Quota ALL, Cali 1100 (1994-1997), Cali EV, V35 ALL, V50 ALL, V65 ALL, V75 ALL, Strada 750, 750 Targa, 750 SP, Nevada 350 (1991-1998), Nevada 750 (1991-1998), V11 Sport, Bellagio, Breva 850, Breva 1100, Breva 1200, Stelvio, Norge, Griso, Cali 1400 ALL

Dimensions:
68mm OD

Rear crankcase oil seal or rear main oil seal.

Fits Nevada 750 up to engine LT017877 and Nevada 350 to engine PC053625. Also known as Guzzi ref. 90405368. We recommend replacing the rear crank oil seal when replacing the clutch

part in stock More than 5 in stock

90405367-z 90405367 GU90405367 90 40 53 67
9040 5367 9040.5367 90.40.53.67

£14.00

INC VAT

£11.67 EX VAT this is the price you will pay if you are ordering from outside the UK

Oil Filter UFI 2314900

SIA14530 Fits 125 2C, 250 TS, S3, 850/1000 ALL Models, Daytona 1000

Dimensions:
For 16mm threaded spigot

Cartridge oil filter UFI 23 149 00

Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.

You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket). Please note that Daytona RS and T5 Polizia use filter SIA15300

part in stock More than 5 in stock

14153000 GU14153000 14 15 30 00
1415 3000 1415.3000 14.15.30.00

£10.50

INC VAT

£8.75 EX VAT this is the price you will pay if you are ordering from outside the UK

Oil Filter UFI 2546500

SIA19530 Fits V35 I, V35 II, V35 3 (pre 1989), V35C, Imola, Imola 2, V50 I, V50 II, V50 3, V50C, Monza, Monza 2 (pre 1989), V65, Lario, V65 Florida (pre 1989), V35 Florida (pre 1989)

Dimensions:
105mm x 45mm diameter overall

UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)

part in stock More than 5 in stock

19153000 GU19153000 19 15 30 00
1915 3000 1915.3000 19.15.30.00

£8.50

INC VAT

£7.08 EX VAT this is the price you will pay if you are ordering from outside the UK

Wheel Bearing Seal

WHA81773 Fits Breva 850, Breva 1100, Breva 1200, 1200 Sport, Norge ALL, Griso ALL, Stelvio, Cali 1400, V85TT

Dimensions:
47mm OD

Used in place of Guzzi ref. AP8125841

part in stock 2 in stock

AP8125773

£23.00

INC VAT

£19.17 EX VAT this is the price you will pay if you are ordering from outside the UK

Bosch Alternator Brush Holder

ELA17452 Fits Cali 2, T3, 750S, S3, 850T, T4, T5 (Series 1), Convert, G5, 1000 SP, SP II, Le Mans 1, Le Mans 2, Le Mans 3, Le Mans 1000, Mille GT (Series 1), V35, V35C, V35 Florida, Imola 2, V35 TT, V50, Monza, V65, V7 Sport

Brush holder for Bosch alternator stator

Also known as Guzzi ref. 17712454, 14712452

Includes brushes. See ELA17453

part in stock 1 in stock

17712452 GU17712452 17 71 24 52
1771 2452 1771.2452 17.71.24.52

£68.30

INC VAT

£56.92 EX VAT this is the price you will pay if you are ordering from outside the UK

Cylinder Head Oil Feed Pipe Set Braided Hose.

ENA14660 Fits 1100 Sport ALL, Cali 1100, Quota ALL, V11 Sport ALL, Le Mans 1000, Le Mans 3, T5, Strada, 1000S, Mille GT, Cali 3, Spada 3, SP II, Cali 2, Cali EV, Cali Stone, Cali Jackal

Dimensions:
Reach of approx. 170mm from central banjo to head

Stainless steel braided hose oil lines for heads on square barrel models. See ENA14662 if you also need threaded link to cylinder head

Always replace crush washers (SIA12200 x 2 and SIA10900 x 2) when replacing oil lines, you may also require our banjo bolt ENA95990. Also known as Guzzi ref. 01153600 and 01153602

part in stock 5 in stock

14153660 GU14153660 14 15 36 60
1415 3660 1415.3660 14.15.36.60

£53.00

INC VAT

£44.17 EX VAT this is the price you will pay if you are ordering from outside the UK

Air Filter UFI 3098900

SIA30360 Fits Daytona, Cali 1100 (1994-1997), Cali EV, V11 Sport, Cali Vintage, Cali Stone, Cali Jackal, Centauro, Quota ALL, 1100 Sport ALL, Bellagio

Dimensions:
220mm x 135mm x 35mm

UFI 30 989 00 flat type air filter, paper filament in rubber surround

See SIA30361 for a reusable K & N air filter

part in stock More than 5 in stock

30113600 GU30113600 30 11 36 00
3011 3600 3011.3600 30.11.36.00

£12.00

INC VAT

£10.00 EX VAT this is the price you will pay if you are ordering from outside the UK

Clutch Pushrod RAM Clutch Extra Long

CLA14086 Fits 850/1000 All Models

Dimensions:
251mm x 6mm

Clutch pushrod for RAM clutch which is 5mm longer than the standard version. This may be needed when fitting a RAM clutch kit to give extra room for adjustment

part in stock 1 in stock

£37.30

INC VAT

£31.08 EX VAT this is the price you will pay if you are ordering from outside the UK

Page 12 of 28

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28