Oil pressure switch. May be supplied with a vertical spade connector, this supercedes the original Guzzi part which is no longer available. This version will fit without removal of the alternator

See ENA12640 for replacement crush washer and ELA10005 for female spade connector

 4 in stock

 31768780 GU31768780 31 76 87 80
 3176 8780 3176.8780 31.76.87.80

Oil pressure switch. May be supplied with a vertical spade connector, this supercedes the original Guzzi part which is no longer available. This version will fit without removal of the alternator

See ENA12640 for replacement crush washer and ELA10005 for female spade connector

 4 in stock

 31768780 GU31768780 31 76 87 80
 3176 8780 3176.8780 31.76.87.80

UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 More than 5 in stock

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Stainless steel exhaust stud kit consisting of 4 x studs, 4 x dome head nuts, 4 x wavy washers and 4 x flat washers

On pre-1998 models we recommend combining with a pair of new exhaust polished aluminium flanges - EXA30032

 More than 5 in stock

 96508040 GU96508040 96 50 80 40
 9650 8040 9650.8040 96.50.80.40

Pair of sintered EBC FA095 HH brake pads for Brembo 5165 single pin four piston calipers

With the highest friction rating and a lifetime which is the envy of other Brake Pad Manufacturers, the Double-H pads are now available in a new quieter running, faster bedding formulation. NB if opting for sintered pads use them all round. We advise checking your front caliper(s) have one not two pad pins

 2 in stock

30654602-z 30654602 GU30654602 30 65 46 02
 3065 4602 3065.4602 30.65.46.02

Output oil seal for drive box

This oil seal fits output side of bevel box

 More than 5 in stock

90407085-z 90407085 GU90407085 90 40 70 85
 9040 7085 9040.7085 90.40.70.85

Full engine and gearbox seal kit, includes all necessary seals for a complete engine and gearbox overhaul.

Full gasket sets also available. Can also be fitted to models equipped with a Saprisa charging system if front crank oil seal ENA94238 is ordered

 More than 5 in stock

 17999550 GU17999550 17 99 95 50
 1799 9550 1799.9550 17.99.95.50

Front oil seal for cam shaft

 More than 5 in stock

90401530-z 90401530 GU90401530 90 40 15 30
 9040 1530 9040.1530 90.40.15.30

Fine thread screw in brakelight switch for linked system proportioning valve or splitter. See ELA12735 for rubber cap

Stop light switch also known as Guzzi ref. 63657000

 More than 5 in stock

 79654116 GU79654116 79 65 41 16
 7965 4116 7965.4116 79.65.41.16

Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 GT/Sport Köwe, Ducati 750 Paso (1984-1992), Ducati 750 Sport, Ducati 750/900 SS Köwe, Ducati 750 F1/Laguna Seca, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR-I, Ducati 900 SS (1990), Ducati 906 Paso (1988), Ducati 1000 MHR-2/S2

Set of ignition points (made up of two boxes of contacts)

 More than 5 in stock

 19709620 GU19709620 19 70 96 20
 1970 9620 1970.9620 19.70.96.20