A4 marine grade stainless steel M6 bleed nipple for Brembo F05 and twin bleed P2 F08 & F09 calipers. Manufactured specially for Gutsibits as a replica of the original Brembo M6 bleed nipple
Use M10 bleed screw SSA36794 for single bleed (later) P8 calipers. Ducati ref. 079539787
See BRA36794 for rubber cap
More than 5 in stock
Also fits Benelli 250 TS, Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 F1/Laguna Sec, KTM 250XC, KTM 250SX, KTM 250EXC,
£8.00
INC VAT
£6.67 EX VAT
5 pin mini relay
Also known as Guzzi ref. 30732560 Can be used in place of 4 pin mini relay ELA01561. We recommend keeping a spare one in your tool kit
More than 5 in stock
01731760 GU01731760 01 73 17 60
0173 1760 0173.1760 01.73.17.60
£14.00
INC VAT
£11.67 EX VAT
Swing arm pivot stub, metric fine thread. See TRA92780 for cover nuts. Replaces Guzzi ref. 14547000
2 in stock
14547001 GU14547001 14 54 70 01
1454 7001 1454.7001 14.54.70.01
£15.50
INC VAT
£12.92 EX VAT
Front crank oil seal for models with Bosch or Ducati charging systems
Also known as Guzz ref. 90402839
More than 5 in stock
90402840-Z
£9.50
INC VAT
£7.92 EX VAT
Brakelight switch
Stop light switch also known as Guzzi ref. AP8224192
See FRA98412 for mounting screw
2 in stock
03749845-z 03749845 GU03749845 03 74 98 45
0374 9845 0374.9845 03.74.98.45
£15.50
INC VAT
£12.92 EX VAT
Brakelight switch for handlebar mounted master cylinder
Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815 or ELA30860. Sometimes supplied with three terminals, in this instance disregard middle terminal. Please note that terminals are smaller than standard switch and will need to be soldered on.
3 in stock
30749860 GU30749860 30 74 98 60
3074 9860 3074.9860 30.74.98.60
£13.50
INC VAT
£11.25 EX VAT
UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick
For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633
More than 5 in stock
27153085 GU27153085 27 15 30 85
2715 3085 2715.3085 27.15.30.85
£9.50
INC VAT
£7.92 EX VAT
Output oil seal for drive box
This oil seal fits output side of bevel box
More than 5 in stock
90407085-z 90407085 GU90407085 90 40 70 85
9040 7085 9040.7085 90.40.70.85
£14.00
INC VAT
£11.67 EX VAT
Full engine and gearbox seal kit, includes all necessary seals for a complete engine and gearbox overhaul.
Full gasket sets also available. Can also be fitted to models equipped with a Saprisa charging system if front crank oil seal ENA94238 is ordered
2 in stock
17999550 GU17999550 17 99 95 50
1799 9550 1799.9550 17.99.95.50
£75.00
INC VAT
£62.50 EX VAT
Swing arm pivot stub, metric fine thread. See TRA92780 for cover nuts. Replaces Guzzi ref. 14547000
2 in stock
14547001 GU14547001 14 54 70 01
1454 7001 1454.7001 14.54.70.01
£15.50
INC VAT
£12.92 EX VAT