UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick
For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)
More than 5 in stock
19153000 GU19153000 19 15 30 00
1915 3000 1915.3000 19.15.30.00
£8.50
INC VAT
£7.08 EX VAT
Cartridge oil filter UFI 23 149 00
Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.
You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket).
Please note that Daytona RS and T5 Polizia use filter SIA15300
More than 5 in stock
14153000 GU14153000 14 15 30 00
1415 3000 1415.3000 14.15.30.00
£10.50
INC VAT
£8.75 EX VAT
Sealed swing arm taper needle roller bearing
Bearing is sealed on one side (not pictured). See FRA92225 for related dust seal
2 in stock
92249224 GU92249224 92 24 92 24
9224 9224 9224.9224 92.24.92.24
£42.00
INC VAT
£35.00 EX VAT
Sealed swing arm taper needle roller bearing
Bearing is sealed on one side (not pictured). See FRA92225 for related dust seal
2 in stock
92249224 GU92249224 92 24 92 24
9224 9224 9224.9224 92.24.92.24
£42.00
INC VAT
£35.00 EX VAT
Cartridge oil filter
For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633
3 in stock
1A023949
£18.00
INC VAT
£15.00 EX VAT
Fork dust cover
4 in stock
AP8163097
Also fits Aprilia Pegaso 650, Aprilia RXV 450
£12.60
INC VAT
£10.50 EX VAT
Sealed ball bearing used as rear wheel bearing for cast and spoked wheels
2 bearings required per wheel. Also used as front wheel bearing in spoked wheels on these models: Cali 1100, S3, T3, G5, Mille GT, Cali 3, Convert, Strada 1000, 1000S, Cali Jackal, Cali Stone, Cali Special (tube rim), Cali Vintage (tube rim), Cali Classic (2006-2007), 850 GT (disc braked version). Front wheel only for 750S / V7 Sport.
More than 5 in stock
92204220-z 92204220 GU92204220 92 20 42 20
9220 4220 9220.4220 92.20.42.20
£10.00
INC VAT
£8.33 EX VAT
Front wheel bearing, sealed
2 bearings required per wheel, Also used as rear wheel bearing on V7 850
More than 5 in stock
92204221 GU92204221 92 20 42 21
9220 4221 9220.4221 92.20.42.21
£10.80
INC VAT
£9.00 EX VAT
Bearing used as UJ carrier bearing on pre 2007 models (see TRA90062 for retaining circlip). Used as outer crownwheel carrier bearing on CARC units
4 in stock
92204230 GU92204230 92 20 42 30
9220 4230 9220.4230 92.20.42.30
£14.40
INC VAT
£12.00 EX VAT
Rubber tank fastening strap
Used as battery strap on V11 and Daytona
More than 5 in stock
14102600-z 14102600 GU14102600 14 10 26 00
1410 2600 1410.2600 14.10.26.00
Also fits Benelli 650 Tornado
£9.50
INC VAT
£7.92 EX VAT