Pair of chromed Tommaselli handlebars, low rise
Also known as Guzzi ref. 30600310, 65600300, 17600360
2 in stock
30600310 GU30600310 30 60 03 10
3060 0310 3060.0310 30.60.03.10
£50.40
INC VAT
£42.00 EX VAT
Pair of sintered EBC FA256 HH rear brake pads
High performance sintered pads with twin pin pin fitting. Pre 2012 V7 models use a different brake pad with only one pad pin hole. Also known as Guzzi ref 2R000248
1 in stock
AP8133798
£22.50
INC VAT
£18.75 EX VAT
The innovative stahlbus bleeder valve allows you to change the brake fluid yourself without assistance.
Linked Guzzi brake systems are notoriously tricky to bleed, this special bleed nipple can save you hours of tedious squeezing and pumping! This banjo bolt can be used in place of a standard fine thread M10 banjo bolt. Supplied with crush washers. We recommend fitting one of these brake valves per caliper
The innovative stahlbus vent valve allows you to change the brake fluid easily and without help. Clean, totally safe and fast !
This auto bleed valve combines all these advantages:
This part is due back in stock soon, call 01484 841395 to reserve yours
£33.00
INC VAT
£27.50 EX VAT
Large dust cover for your bike when parked up in your garage. Prevents dust and dirt settling on your pride and joy. Also useful for hiding your bike from prying eyes when your garage door is open. Also see tank protector SIA00001 for extra protection.
Breathable, tear resistant fabric.
Order now and we will post your order within 7 days.
£19.00
INC VAT
£15.83 EX VAT
The Mistral V-Twin boost is an effective and cost efficient way to cure the fuelling problems common to all modern fuel injected Guzzi's. The V85 TT runs particularly lean and will benefit more than most bikes from the installation of a V-Twin Boost.
Plugging directly into the wiring harness using original connectors, with no cutting or splicing required, installation takes less than ten minutes.
The V-Twin boost features a unique technology to provide your bike with a controlled fuel enrichment.
Make your bike run as it should have done from the factory!
This part is due back in stock soon, call 01484 841395 to reserve yours
£115.00
INC VAT
£95.83 EX VAT
Iridium LMAR8EI-7 spark plug
This part is due back in stock soon, call 01484 841395 to reserve yours
1D001003
£18.00
INC VAT
£15.00 EX VAT
Pair of EBC FA018 brake pads for P2 F08 (P8) calipers.
For P08/F08 calipers. Front and rear pads for all models except P9 equipped Spada where these are only for front calipers
More than 5 in stock
28654601-z 28654601 GU28654601 28 65 46 01
2865 4601 2865.4601 28.65.46.01
Also fits Benelli 354 Rear, Benelli Sei Fronts, Ducati 250/350/450 Desmo Fronts (-1976), Ducati Pantah, Ducati F1, Ducati 750 Paso Fronts (1987-1990), Ducati 750 Sport (1988-1990), Ducati 860 GT/GTS, Ducati 900 GTS, Ducati Hailwood Rep, Ducati 900 Darmah (1977-1978), Ducati 906 Paso (1988-1989), Ducati 1000 R1 Hailwood Ref., Hesketh, Horex HRD 600, Horex 500/600 Columbus, Laverda 750 SF2 Fronts, Laverda 750 SFC, Laverda 750 SF3, Laverda 1000 3C (1974-1978), Laverda 1000 3CL (1976-1981), Laverda 1000 RGS/RGA, Laverda 1000 RGS Corsa Rear, Laverda 1000 SFC, Laverda 1200 (1978-1979), Laverda 1200 TS/Mirage (1981), MZ ETZ 125/150/250/300 Fronts (1985-1992), Norton Classic (1989), Norton Interpol (1989), Triumph T140 (1985-1988 Brembo)
£19.30
INC VAT
£16.08 EX VAT
Cartridge oil filter UFI 23 149 00
Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.
You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket).
Please note that Daytona RS and T5 Polizia use filter SIA15300
More than 5 in stock
14153000 GU14153000 14 15 30 00
1415 3000 1415.3000 14.15.30.00
£10.50
INC VAT
£8.75 EX VAT
Reproduction chain tensioner for rear wheel spindle. The axle passes through the head of this chain adjuster
This part is available by special order, request a quote
10336300-z 10336300 GU10336300 10 33 63 00
1033 6300 1033.6300 10.33.63.00
£44.00
INC VAT
£36.67 EX VAT
High rise chromed handlebars with cross brace
These can be fitted to pre 1979 models but you will need to drill the bars to allow switchgear wiring to be correctly routed through the handlebars
This part is available by special order, request a quote
17600270 GU17600270 17 60 02 70
1760 0270 1760.0270 17.60.02.70
£75.00
INC VAT
£62.50 EX VAT