UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick, If this item is out of stock we do stock a like for like replacement, which is this item SIA27301 .

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85

Dimensions:
120mm x 45mm diameter overall

Chrome finish plastic CEV 18343 type indicator with amber lens and 21W bulb

Indicator mounts available separately, see LIA19751. Also known as Ducati part 079903444.1 079903444.2

18750656-z 18750656 GU18750656 18 75 06 56
 1875 0656 1875.0656 18.75.06.56

Also fits Ducati Pantah, Most Ducati Bevels

Dimensions:
70mm diameter lens, M10 mounting socket

Dellorto choke piston or plunger for Dellorto VHB, PHBH, PHF and PHM carbs. Includes rubber seal in end of plunger

 13937800 GU13937800 13 93 78 00
 1393 7800 1393.7800 13.93.78.00

Dimensions:
8mm OD x 21mm overall

Brembo rebuild kit for Brembo F05 (P5) calipers with 32mm pistons. Contains 2 bolts, all seals and brake grease

This caliper also known as P2 F05N, P32B and P32F.
This seal kit also known as Brembo ref. 120279910, also used on Benelli 504 Sport, 650 Al'Azzura, Ducati 500s, Laverda 500 Montjuich and Zeta (front) and Bimota DB1 and YB4 (rear).

Not suitable for P32 rear calipers fitted to 750T and Nevada 750 (1991-2001) - see BRA01723 for this model. Will not fit pistons on Grimeca F05 calipers.

 39659000 GU39659000 39 65 90 00
 3965 9000 3965.9000 39.65.90.00

Also fits Benelli 504 Sport, Benelli 250 TS, Ducati Pantah 500SL, 650 Al'Azzura, Ducati 500s, Laverda 500 Montjuich and Zeta (front) and Bimota DB1 and YB4

Dellorto choke piston or plunger for Dellorto VHB, PHBH, PHF and PHM carbs. Includes rubber seal in end of plunger

 13937800 GU13937800 13 93 78 00
 1393 7800 1393.7800 13.93.78.00

Dimensions:
8mm OD x 21mm overall

Drive box input seal

Pinion oil seal

90403251-z 90403251 GU90403251 90 40 32 51
 9040 3251 9040.3251 90.40.32.51

Dimensions:
47mm OD

Bearing used as UJ carrier bearing on pre 2007 models (see TRA90062 for retaining circlip). Used as outer crownwheel carrier bearing on CARC units

 92204230 GU92204230 92 20 42 30
 9220 4230 9220.4230 92.20.42.30

Dimensions:
62mm OD

Round 12v two pin flasher relay

See FRA17720 for rubber mount, item may look different to this please take into consideration before ordering.

 17750520 GU17750520 17 75 05 20
 1775 0520 1775.0520 17.75.05.20

Dimensions:
32mm diameter

Oil pressure sender, M12 thread, male bullet connector

This oil pressure sensor supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.

See ENA12640 for replacement crush washer if required

 17768750 GU17768750 17 76 87 50
 1776 8750 1776.8750 17.76.87.50

Dimensions:
M12 thread, 46mm x 21mm bolt flats

Fine thread screw in brakelight switch for linked system proportioning valve or splitter. See ELA12735 for rubber cap

Stop light switch also known as Guzzi ref. 63657000

 79654116 GU79654116 79 65 41 16
 7965 4116 7965.4116 79.65.41.16

Also fits Ducati 350-500 Twin, Ducati 350-500 Twin GTV, Ducati 350-500 Twin Sport, Ducati 500 SL Pantah, Ducati 500 Sport Desmo, Ducati 600 SL Pantah, Ducati 750 GT/Sport Köwe, Ducati 750 Paso (1984-1992), Ducati 750 Sport, Ducati 750/900 SS Köwe, Ducati 750 F1/Laguna Seca, Ducati 860/900 GTS, Ducati 900 Darmah, Ducati 900 MHR-I, Ducati 900 SS (1990), Ducati 906 Paso (1988), Ducati 1000 MHR-2/S2

Dimensions:
M10 fine thread