Brand new budget starter motor and solenoid suitable as a direct replacement for Guzzi Valeo and Bosch 8 or 9 teeth starter motors. You may need to fit hex headed neutral switch bolts on some pre 1990 models to make room for the solenoid. Our part number for the bolt is SSA06016 Please note that this item may be fitted to Loop frame models with some modifications as described in Guzziology, also see https://www.thisoldtractor.com/moto_guzzi_loopframe_starter_-_how_to_replace_the_magneti_marelli_starter_with_a_valeo.html for advice on this upgrade.

Supercedes Guzzi refs. 12730705, 14730554 and 14730705

Get a discount of £20 on this item if you part exchange your existing faulty Valeo or Bosch starter motor.

 1 in stock

 30730711 GU30730711 30 73 07 11
 3073 0711 3073.0711 30.73.07.11

Short alloy bellmouth / trumpet intake with domed mesh for Dellorto PHF 30 and 36 carbs, screws to rear of carb replacing air filter

 2 in stock

Dellorto choke jet size 60

 2 in stock

Dellorto choke jet size 70

 2 in stock

 14936050 GU14936050 14 93 60 50
 1493 6050 1493.6050 14.93.60.50

Pair of universal Domino chromed handlebars, medium rise.

Not suitable for V65 GT, Mille GT or other models with wide handlebar clamps - see dimensions if in doubt about suitability for your bike

 1 in stock

UFI 30 814 00 flat type air filter, paper filament in rubber surround

NB Packaging may vary

 More than 5 in stock

 28113650 GU28113650 28 11 36 50
 2811 3650 2811.3650 28.11.36.50

Air filter, flat paper cartridge type

See SIA10433 for a reusable K & N air filter

 More than 5 in stock

AP8104329

UFI 25 46 500 cartridge oil filter. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For post 1989 V35, V50 and V65 models use SIA27300 .
NB Packaging may vary. For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer)

 More than 5 in stock

 19153000 GU19153000 19 15 30 00
 1915 3000 1915.3000 19.15.30.00

Cartridge oil filter UFI 23 149 00

Fits Daytona 1000 models where filter screws into base of sump. This is an 8 sided UFI filter.
Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump.

You may also require SIA10070 which is the crush washer for the drain plug and ENA14036 (sump gasket). Please note that Daytona RS and T5 Polizia use filter SIA15300

 More than 5 in stock

 14153000 GU14153000 14 15 30 00
 1415 3000 1415.3000 14.15.30.00

UFI 25 531 00 cartridge oil filter for 1989 on small block engines. See TOA19001 for a inexpensive tool to loosen and tighten the dipstick

For an oil change we also recommend 1x ENA90444 (Oil filter cover O ring), 1 x SIA10070 (large sump drain crush washer), 1 x SIA10900 (small sump drain crush washer) and 1 x SIA12200 (filter cover crush washer). Some 750 XPA models use SIA19530, we advise you to check your old filter before ordering. Also known as Guzzi ref. 2A000633

 More than 5 in stock

 27153085 GU27153085 27 15 30 85
 2715 3085 2715.3085 27.15.30.85