Oil pressure sender

Can also be used in place of oil pressure switch 17768750 and adapter 19055800 on Monza (check which type your small twin uses before replacing). Replaces two part sensor 31999581.

See ENA12640 for replacement crush washer if required

 3 in stock

19768720-z 19768720 GU19768720 19 76 87 20
 1976 8720 1976.8720 19.76.87.20

Pair of FAC air assisted fork dampers. These are a major suspension upgrade for the front end of your bike and work best when combined with progressive fork springs SUA18961

Stainless steel damper rod and alloy top nut, supplied with fork top O ring. Pressurise to between 7 and 29 PSI. See OIA01001 for ATF (used in place of fork oil)

 1 in stock

14526455-z 14526455 GU14526455 14 52 64 55
 1452 6455 1452.6455 14.52.64.55

Also fits Benelli Sei 900

Breather valve and filler plug for drive box and CARC units

Can be used in place of Guzzi ref. GU05206530, 2A000438 and 2A000823
See SIA10900 for related crush washer

 1 in stock

 19206501 GU19206501 19 20 65 01
 1920 6501 1920.6501 19.20.65.01

Throttle cable, runs from twistgrip to carb

Ball end at twistgrip

 2 in stock

13117565-z 13117565 GU13117565 13 11 75 65
 1311 7565 1311.7565 13.11.75.65

Brembo kit containing replacement seal and angled elbow for connecting remote brake fluid reservoir to PS 15, PS 11 and PS 13 rear master cylinders

Also known as Brembo ref. 110312720

 3 in stock

 19659500 GU19659500 19 65 95 00
 1965 9500 1965.9500 19.65.95.00

Riders footpeg rubber, black with chamfered underside

 More than 5 in stock

39443200-z 39443200 GU39443200 39 44 32 00
 3944 3200 3944.3200 39.44.32.00

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Oil return pipe with threaded union for sump

Can be used in place of GU32159310 on late V7 models if pipe is cut and breather valve from old pipe inserted into cut section.
Uses crush washer SIA12200

 4 in stock

27159360-z 27159360 GU27159360 27 15 93 60
 2715 9360 2715.9360 27.15.93.60

Black rubber UJ gaiter / boot, clips available separately - see SSA64990 and TRA12544

 More than 5 in stock

 18548000 GU18548000 18 54 80 00
 1854 8000 1854.8000 18.54.80.00

Brakelight switch for handlebar mounted master cylinder

Stop light switch also known as Guzzi ref. 30530526. Please compare with your existing switch to check compatibility. Can be used as a substitute for ELA27815. See ELA30861 for less expensive alternative part. Sometimes supplied with three terminals, in this instance disregard middle terminal

 4 in stock

 30749860 GU30749860 30 74 98 60
 3074 9860 3074.9860 30.74.98.60